Silicon ChipWorking with switch-mode power supplies - December 2026 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: I seriously underestimated AI coding
  4. Feature: The History of AMD, Part 2 by Dr David Maddison, VK3DSM
  5. Project: Advanced Cable Analyser by Richard Palmer
  6. Project: Inrush Current Limiter by Phil Prosser
  7. Feature: Motor Control, Part 3 by Andrew Levido
  8. Project: NeoPixel RGB LED Analog Clock, Part 2 by Nicholas Vinen
  9. Feature: Working with AVR & PIC Fuses, Part 1 by Tim Blythman
  10. PartShop
  11. Project: The Magic Candle by Dr Hugo Holden
  12. Serviceman's Log: Working with switch-mode power supplies by Malcolm Batchelor et al
  13. Vintage Radio: STC Bantam model A141 by Ian Batty
  14. Subscriptions
  15. Market Centre
  16. Advertising Index
  17. Notes & Errata: PicoSDR, April 2026
  18. Outer Back Cover

This is only a preview of the December 2026 issue of Silicon Chip.

You can view 37 of the 104 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Articles in this series:
  • The History of AMD, Part 1 (November 2026)
  • The History of AMD, Part 2 (December 2026)
Items relevant to "Advanced Cable Analyser":
  • Advanced Cable Analyser main PCB [04101261] (AUD $5.00)
  • Advanced Cable Analyser lid PCB [04101262] (AUD $10.00)
  • Advanced Cable Analyser software and documentation (Free)
  • Advanced Cable Analyser PCB patterns (PDF download) [04101261-2] (Free)
  • Cutting/drilling diagrams for the Advanced Cable Analyser (Panel Artwork, Free)
Items relevant to "Inrush Current Limiter":
  • Inrush Current Limiter PCB [10110261] (AUD $7.50)
  • Inrush Current Limiter PCB pattern (PDF download) [10110261] (Free)
Articles in this series:
  • Motor Control, Part 1 (October 2026)
  • Motor Control, Part 2 (November 2026)
  • Motor Control, Part 3 (December 2026)
Items relevant to "NeoPixel RGB LED Analog Clock, Part 2":
  • BZ-121 miniature GNSS receiver (Component, AUD $30.00)
  • Neo-7M GPS module with onboard SMA connector & 5-pin header (Component, AUD $20.00)
  • VK2828U7G5LF TTL GPS/GLONASS/GALILEO module with antenna and cable (Component, AUD $25.00)
  • New RGB LED 'Analog' Clock kit (Component, AUD $85.00)
  • New RGB LED 'Analog' Clock firmware (Software, Free)
Articles in this series:
  • NeoPixel RGB LED Analog Clock, Part 1 (November 2026)
  • NeoPixel RGB LED Analog Clock, Part 2 (December 2026)
Items relevant to "The Magic Candle":
  • Magic Candle PCB [05112251] (AUD $2.50)
  • Magic Candle PCB pattern (PDF download) [05112251] (Free)
  • Magic Candle assembly diagrams (Panel Artwork, Free)

Purchase a printed copy of this issue for $15.00.

SERVICEMAN’S LOG Working with switch-mode power supplies O ften I work on cancer treatment machines that use a couple of 16-port managed network switches. These switches usually function perfectly for over a decade, but occasionally one fails. A colleague came up with the idea of removing the faulty switch-mode PSU (SMPS) and replacing it with one from an older, unused machine if available. This avoids the hassle of waiting for a new switch to be ordered, delivered and reconfigured. Replacing the PSU is a quick and easy fix. It involves removing four screws from the cover and the four securing the PSU. I’ve always been curious about how these ubiquitous devices work. I’ve replaced many SMPSs over the years because they’re considered field-replaceable and never repaired. Recently, another SMPS failed and was replaced. This time, I decided to try repairing one myself. I did some internet searches on SMPS theory to refresh my understanding. A few years earlier, I’d delved deep into power electronics while fixing an old split system air conditioner that no one else could repair. I found the recent series of articles in Silicon Chip on the subject (Power Electronics; siliconchip.au/Series/452) particularly interesting. It was a shame they hadn’t been published five years ago! I eventually repaired the air conditioner, which only finally gave up the ghost a few months ago due to a gas leak. The next challenge was finding a circuit diagram for the SMPS. It turns out that this particular SMPS is used in a wide range of devices. I managed to get a circuit diagram that, while not exactly the same as my PSU, was close enough to help me figure out what was happening. The SMPS occasionally powered on OK, but not very often. I began by checking the input-side components. The bridge rectifier output was around 300V DC, which was tapped off using a couple of high-value resistors to power the controller chip. Apparently, once the device is working correctly, the chip receives power from a rectified secondary winding in the transformer. I wasn’t sure why this was the case, but since the device operates at some kHz, the secondary supply might produce a smoother voltage. Editor’s note: it’s likely to improve the power factor and efficiency of the device. I then checked the controller chip’s output pin and expected to see a square wave at some multi-kHz frequency. However, the output frequency was surprisingly low, which seemed odd. Further reading up on SMPS theory revealed that when the PSU had no load, it would enter power-saving mode. A minimum load current is required to prevent it from going into standby. I soldered an appropriate value resistor to the output pads to draw current, but that didn’t help. I removed and tested the Mosfet, rectifier diodes, snubber diode and a few other usual suspects. I had recently bought a tweezer-style in-circuit tester but, being a bit oldschool, I wasn’t entirely convinced of the results. For example, the output rectifier diodes were measuring about 0.9V, which seemed a little strange. They were part of a dual pack and, after checking the spec sheet, I discovered that they were fast recovery diodes with a forward voltage in the range I was reading. Another mystery solved. I also learned something interesting about Mosfets during this process. You can switch them on out of circuit using the diode test mode on your DVM. Apparently, you can charge the gate with the DVM and it stays charged for a Items Covered This Month • Fixing the power supply in cancer treatment machines • Two HP laptop repairs • Repairing a clock for preschool children • A simple fix for flickering • Dyson bladeless fan repair Cartoonist – Louis Decrevel Website: loueee.com 88 Silicon Chip Australia's electronics magazine siliconchip.com.au while, which gives you curious results when checking the drain-source resistance. Sometimes the drain source was over-range, sometimes short circuit. Coincidentally, I stumbled across a YouTube video at about the same time. It featured an electronics technician explaining that you couldn’t trust component testers with Mosfets. This memory came in handy when I was getting strange results testing my Mosfet. After testing it correctly, I realised it was fine and soldered it back into the PCB. As you might know, these PSUs have a feedback loop to control the output voltage. Feedback systems can be tricky to fault-find. I was aware that there are various techniques to diagnose feedback systems, but hadn’t delved into them much before. One approach I considered was to break the loop and feed an external control voltage into the control chip, then fault-find the system linearly afterwards. Since the PSU only operated correctly on occasion, I couldn’t get readings for normal voltages in the circuit. I wanted to break the feedback loop at the opto-coupler and feed an appropriate voltage forward from there. However, not knowing an appropriate voltage, I decided to just wing it and removed the opto-coupler. I switched the PSU back on, and this time it was working. I was instantly reminded of one formula: P = I2R. The load resistor had gone up in smoke! I’d used a 1W resistor, but its value was low enough to result in a dissipation much higher than that. I had some low-value 5W resistors lying around, so I soldered in a replacement. It occurred to me that the unregulated output voltage might not be a small percentage higher than the nominal voltage, as I’d expected. It could be quite a lot higher, explaining why the original output resistor had fried. The 5W resistor might not have survived the excess voltage either, but I might have had enough time to switch off the PSU before it fried as well. Before continuing, I decided to solder a flying lead to the transformer pin connected to the Mosfet drain so I could attach an oscilloscope probe while checking other circuit parts with a DVM. However, I noticed that the solder on the pad didn’t flow as expected. It remained grey, not turning silver when melted as anticipated. This made me wonder about dry joints. I then desoldered all the transformer pins and the solder on each behaved identically. I was confident I’d nailed it. I resoldered all the joints with fresh solder and powered the PSU back on. A steady 5V output appeared, and now it powered back on reliably every time I switched it off and on again. The switch drew a lot less than the 6A maximum rating current of the PSU, and the case was ventilated, so I doubted the transformer was getting too hot. However, it may still have been hot enough to compromise the solder joints over many heat cycles. Who knows? The rest of the components’ solder joints that I looked at during my troubleshooting all flowed as expected, including the power Mosfet driving the transformer. I suspect every PSU of this type would fail in the same way. As with many pieces of equipment, electrical, electronic, mechanical etc, there are common failure modes. Once known, repairs become straightforward. Whether it’s practical to repair is another question. Since the repaired switch won’t be going back into a siliconchip.com.au machine, it’ll likely end up with my son, a programmer with a few PCs he’s about to network together. Overall, it’s always satisfying to fix something yourself and learn something along the way. Malcolm Batchelor, Parramatta, NSW. HP dv5 laptop repair My son picked up this HP dv5 laptop at the tip shop a few weeks ago. I could see it needed a lot of work but the potential was there. When I first tested it, I found that it worked but the keyboard had three missing keys. I obtained a replacement keyboard via eBay, as I didn’t have one in my salvaged keyboard collection. It came with an Intel P8400 processor at 2.26GHz, but I could upgrade it to an Intel P8600 processor at 2.4GHz. The CR2032 cell that keeps the CMOS data and the time and date current was under a cover on the back of the laptop, so it was easily accessible. More often than not, I need to fully dismantle the laptop to replace the cell, which I have done many times. I would be dismantling this laptop anyway, to clean the CPU heatsink and fan, and upgrade the CPU. With the laptop apart, I removed the motherboard, then detached the heatsink and fan as an assembly. This laptop has a dual heatsink for the CPU and GPU. The fan is attached to the heatsink with three tiny screws and a piece of tape. With it removed, I could see that both heatsinks were about 20% clogged, which isn’t too bad. Of greater concern was that the heatsink compound had dried out completely, which is also common with these old laptops (it’s 18 years old). The motherboard will support an Intel P9600 CPU at 2.53GHz, but I did not have one, so I dropped in the P8600, which isn’t far behind. I reassembled the laptop and then fitted the replacement keyboard. This laptop came with 4GB of PC2 RAM and a 320GB hard drive, which I will reuse. I don’t know what’s on the hard drive; I’ll just wipe it when I install Linux. Installing Linux, I realised there was a problem. When Australia's electronics magazine December 2026  89 The HP dv5 laptop (shown above) that Bruce Pierson picked up from a tip shop. The photos opposite, at lower right, show another HP-branded laptop that had a broken case. I was setting the time and checking other settings, I could see that there was a blemish in the screen that I had not noticed when I’d done a quick test before dismantling the laptop. It looked like something was inside the screen, even though the full picture was there. Time to take the laptop apart again to replace the screen. It’s easy to remove the lid as it just entails removing the panel above the keyboard, the keyboard and the wiring. Then the hinges are easily accessible without having to remove the top shell, so it’s not much of a job to get the lid free. With the lid off, I removed the two screws, pulled off the screen surround, removed the other screws and then disconnected the screen. It is different to most laptop screens as it has a separate plug for the backlight. I looked through all the screens I had in my electronics workshop and I came up empty. I had some screens in two boxes down in the back shed from laptops that I’d wrecked years ago, so I went down to look through the boxes, hoping to find a compatible screen. 90 Silicon Chip Nothing in the first box, and I was almost to the bottom of the second box when I found two screens that looked like they were from the same family as the faulty screen. It happened that one was identical, with the same brand and the same part number as the faulty screen. The other screen was a different brand, but it looked identical also, with the same 30-pin connector for the screen and the separate plug for the backlight. I tested both screens and they were both good. I selected the screen that was a different brand as it was slightly brighter than the identical screen. The next day, I started installing the new screen and I found that the screws I had neatly arranged on the workbench when I dismantled the lid were mostly not there now! I looked on the floor and found several of them, but some were missing. It looks like I had an overnight visitor who messed up my system. I suspect that it was a green tree frog, as I previously saw one on the floor inside my electronics workshop. It must have jumped up on the workbench and sent the screws flying. As I was missing several screws, I had to search through a container of screws to find replacement screws of the correct size. Finally, I could reassemble the lid, refit it and finish assembling the laptop again. I decided to try Big Linux. It has a KDE Plasma desktop that is highly customisable. The ISO installer file is 5.2GB, so it needs to be burned to a double-layer DVD. I booted up the laptop and now there was another problem. I could hear the DVD drive making grinding noises partway through loading the files. I powered the laptop off, removed the optical drive and looked through my box of salvaged optical drives. I found an identical one with the same faceplate. However, when I tried to fit it, it would not engage the connector, so I got another drive, changed the faceplate and it fitted correctly. This time it loaded. Unfortunately, after I installed it, I could only get a resolution of 640 × 480 pixels, even after updating the video drivers, so I’ll have to try it again on a newer laptop later. The best Linux distros for older hardware are Lubuntu, Kubuntu and Linux Mint Cinnamon, which also have the advantage of being more like Windows XP with their applications menu (start menu). I recently set my wife up with Australia's electronics magazine siliconchip.com.au Linux Mint Cinnamon on a Sony Vaio laptop with an i7 processor and 8GB of RAM. She said it’s much faster than her old Windows 10 laptop and she is very happy with it. With so many older and even more recent laptops and computers not supporting Windows 11, Linux can save these laptops and computers. While Linux may not be suitable for anyone with specific software needs, it’s fine for use as an operating system for anyone who just does email, web browsing, YouTube and online banking, which is what my wife does. Linux distros that are based on Ubuntu have a massive library of free applications that will cover the needs of most users. So with a bit of work and some replacement parts that I either had on hand or could get via eBay, this old HP dv5 laptop now has a new lease on life and that’s another one saved from the junk pile. I’ve found that there are many sellers on eBay, and likely other online stores, who stock parts for these old laptops. It is sometimes necessary to order parts from overseas but a bit of searching usually turns up any required parts. Bruce Pierson, Dundathu, Qld. HP 15 Laptop repair Continuing with another laptop; when I got this HP 15 laptop with an i7-4500U 1.8GHz processor, I tested it and found that it worked, but the back right-hand corner of the bottom shell was broken. It just happened that I had a nearly identical laptop with an AMD processor that did not work, so I was hoping that I could use the bottom shell from it to repair this laptop. However, when I dismantled the donor laptop, I found that the bottom shell was also broken, with the nuts for the hinges ripped out and some other damage, so I couldn’t use it. However, the part that was broken on the otherwise good laptop was still OK on the broken one, so it was just a matter of removing it from the bottom shell. siliconchip.com.au Servicing Stories Wanted Do you have any good servicing stories that you would like to share in The Serviceman column in SILICON CHIP? If so, why not send those stories in to us? It doesn’t matter what the story is about as long as it’s in some way related to the electronics or electrical industries, to computers or even to cars and similar. We pay for all contributions published but please note that your material must be original. Send your contribution by email to: editor<at>siliconchip.com.au Please be sure to include your full name and address details. I found that it was clipped on, but it had some small tabs that had been melted over as well. I started prying it off the bottom shell and it popped off without too much trouble, with the melted-over tabs giving way easily. I went through the process of dismantling the good laptop, and once I had everything out of the bottom shell, I prised off the broken part so I could replace it. I gave everything a quick clean and then proceeded to attach the new part, which clipped on easily and sat in place nicely. Now it was time to reassemble the laptop and get it ready for an operating system. This laptop does not have a CR2032 cell to power the CMOS, but it instead relies on the main battery to keep the time and date correct. Fortunately, the battery in this laptop is still good, unlike another I have that uses a similar scheme. In that case, the time and date need to be reset whenever that other laptop is powered up, which is rather inconvenient. This HP 15 laptop is an entry-level laptop, with the i7 CPU soldered to the motherboard instead of being in a socket. Also, the hard drive is inside the laptop with no bottom access panel. With the laptop put back together, it was time to install Linux on it. I had previously installed Debian on a laptop Australia's electronics magazine December 2026  91 with an Intel i3 processor and found that it was a bit on the slow side, so I would now install it on this laptop with the i7 processor. The installation went smoothly, so another laptop was saved, having a new life with Debian Linux. Bruce Pierson, Dundathu, Qld. Child’s clock repair This clock is designed for preschool children who have not yet learned to tell the time. It is shaped like a traditional wind-up alarm clock but sports a backlit digital display, which shows the time using a 7-segment display, and large LCD icons showing a sun or a moon. The backlight changes colour, illuminating yellow for daytime and blue for nighttime. This means that even little kids can tell at a glance whether it is time to sleep, or to get up and hassle mum and dad. The clock has an internal 500mAh lithium-polymer cell that is charged via a micro-USB socket, using the ubiquitous TP4056 charge controller IC. The battery typically lasts for a week or two between charges. This particular clock has been in service for almost three years, but was no longer charging reliably. It would only charge if the micro-USB cable was held at a very specific angle. Several different USB cables were tried, but the problem remained. Unlike many modern consumer devices, this one was easy to open, with a handful of Phillips screws securing the front and back mouldings of the clock in a clamshell design. The main PCB and battery were mounted on the rear moulding, with the large LCD screen and backlight on the front, joined by a conductive rubber strip. The charging socket was all alone on a tiny PCB ‘daughterboard’ soldered at right-angles to the main PCB. Close inspection showed that the power pins of the micro-USB socket had fatigued loose from the daughterboard. I desoldered the daughterboard, then used two strips of desoldering braid as bridges between the socket’s power pins and the daughterboard. I also built up a thicker fillet of solder around the metal body of the socket, to try to stop it from flexing in the future. I then re-attached the daughterboard to the main PCB with more generous fillets of solder. Now the clock charges reliably again. Nicholas West, Canberra, ACT. A simple LED light bulb repair Some time ago, I purchased two 4W LED globes with Edison screw style bases. They were very cheap as I bought The clock with the front part of the enclosure and display removed. The micro-USB daughterboard can be seen at the bottom of the main PCB. The USB daughterboard; you can see where the socket has flexed and lifted the PCB tracks. The power tracks were repaired using strips of desoldering braid. 92 Silicon Chip Australia's electronics magazine siliconchip.com.au them from an op shop for only one dollar each. Though technically second-hand, they looked new, as they were still in their original packaging. Having glass envelopes, they were well-packed in bubble wrap and cardboard. I unpacked one of them and installed it in my lounge. I tested it and all seemed good. That night, the globe started flickering; oh dear, that’s why they were ‘thrown out’. For the remainder of the night, I put the old globe back in. This confirmed it was the new LED globe and not the wiring or switch at fault. The next day, I decided to investigate further. I could see the nipple of solder at the base of the globe was quite corroded. This is meant to connect to the Active terminal in the socket. I thought surely it wouldn’t be that simple. I very carefully filed the corrosion off the solder and bent the brass contact up a bit. I also decided to add a very small amount of WD40 to the rivets and other contacts that make this globe operate. On testing, all was well, with no flickering. It wasn’t the fact that I got the globe to work properly that I was happy about – it’s that it won’t have to be discarded for a lot longer now. The other globe also had some corrosion on it; maybe they were very old stock, or got damp in storage. Peter Eichhorn, Heathcote, Vic. Dyson AM02 bladeless fan repair This fan was originally released in 2010 at a price of US$450. When I received it from Ewaste Connection in Brisbane, it showed no sign of life. After taking off the base by twisting it and releasing a catch, you gain access to the circuit board. Mains power is connected directly to the board, and the AC power goes via a line filter and fusible link resistor to a full-wave rectifier, then a large capacitor. The voltage on the capacitor is about 340V DC, ie, the peak mains voltage. Connected to the capacitor is an LNK340DN switching regulator IC in a small surface-mount package (SO-8C) to provide a 15V DC supply. This IC has its own internal high-voltage FET. The 15V is used by a 24-pin SMA6863 brushless motor drive IC for its logic circuitry. The SMA6863 has three Mosfet-based half-bridges to drive the fan motor, all powered by the 340V DC supply. The large 6-pin IC on the wiring side is a MOC3082, an optically isolated Triac to drive the rotational motor. A 5V three-terminal regulator, fed from the 15V supply, supplies an ATtiny681 20-pin surface-mounted microprocessor. This IC controls the fan by reading the fan input controls or a remote, and uses its outputs to drive the SMA6863. Measurements showed that the 340V DC supply was OK, but there were no 15V DC or 5V DC rails. By using an external floating 15V, with its negative to the 340V supply capacitor, I found that the 5V regulator is working, and the fan is otherwise functional. I had to disconnect the LNK304’s inductor to avoid feeding the 15V DC back to it. I just have to get a replacement LNK340DN to complete the repair. During this diagnosis, I had trouble reading the IC part numbers due to the conformal coating on the board. I had to scrape this off the ICs to read the part numbers. A solvent capable of removing the coating would be useful, as long as it does not remove the part number as well. SC Roger Sanderson, Figtree Pocket, Qld. siliconchip.com.au Australia's electronics magazine December 2026  93