Silicon ChipPicoSDR, April 2026 - December 2026 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: I seriously underestimated AI coding
  4. Feature: The History of AMD, Part 2 by Dr David Maddison, VK3DSM
  5. Project: Advanced Cable Analyser by Richard Palmer
  6. Project: Inrush Current Limiter by Phil Prosser
  7. Feature: Motor Control, Part 3 by Andrew Levido
  8. Project: NeoPixel RGB LED Analog Clock, Part 2 by Nicholas Vinen
  9. Feature: Working with AVR & PIC Fuses, Part 1 by Tim Blythman
  10. PartShop
  11. Project: The Magic Candle by Dr Hugo Holden
  12. Serviceman's Log: Working with switch-mode power supplies by Malcolm Batchelor et al
  13. Vintage Radio: STC Bantam model A141 by Ian Batty
  14. Subscriptions
  15. Market Centre
  16. Advertising Index
  17. Notes & Errata: PicoSDR, April 2026
  18. Outer Back Cover

This is only a preview of the December 2026 issue of Silicon Chip.

You can view 37 of the 104 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Articles in this series:
  • The History of AMD, Part 1 (November 2026)
  • The History of AMD, Part 2 (December 2026)
Items relevant to "Advanced Cable Analyser":
  • Advanced Cable Analyser main PCB [04101261] (AUD $5.00)
  • Advanced Cable Analyser lid PCB [04101262] (AUD $10.00)
  • Advanced Cable Analyser software and documentation (Free)
  • Advanced Cable Analyser PCB patterns (PDF download) [04101261-2] (Free)
  • Cutting/drilling diagrams for the Advanced Cable Analyser (Panel Artwork, Free)
Items relevant to "Inrush Current Limiter":
  • Inrush Current Limiter PCB [10110261] (AUD $7.50)
  • Inrush Current Limiter PCB pattern (PDF download) [10110261] (Free)
Articles in this series:
  • Motor Control, Part 1 (October 2026)
  • Motor Control, Part 2 (November 2026)
  • Motor Control, Part 3 (December 2026)
Items relevant to "NeoPixel RGB LED Analog Clock, Part 2":
  • BZ-121 miniature GNSS receiver (Component, AUD $30.00)
  • Neo-7M GPS module with onboard SMA connector & 5-pin header (Component, AUD $20.00)
  • VK2828U7G5LF TTL GPS/GLONASS/GALILEO module with antenna and cable (Component, AUD $25.00)
  • New RGB LED 'Analog' Clock kit (Component, AUD $85.00)
  • New RGB LED 'Analog' Clock firmware (Software, Free)
Articles in this series:
  • NeoPixel RGB LED Analog Clock, Part 1 (November 2026)
  • NeoPixel RGB LED Analog Clock, Part 2 (December 2026)
Items relevant to "The Magic Candle":
  • Magic Candle PCB [05112251] (AUD $2.50)
  • Magic Candle PCB pattern (PDF download) [05112251] (Free)
  • Magic Candle assembly diagrams (Panel Artwork, Free)

Purchase a printed copy of this issue for $15.00.

Advertising Index Altronics.................................41-44 Blackmagic Design................. 7, 11 DigiKey Electronics..................OBC Emona Instruments.................. IBC Hare & Forbes............................. 13 Jaycar............................. IFC, 26-29 Keith Rippon Kit Assembly....... 103 LD Electronics........................... 103 LEDsales................................... 103 Microchip Technology.................. 5 Mouser Electronics....................... 3 PCBWay......................................... 9 PE Back Issues............................. 4 PMD Way................................... 103 SC Versatile Battery Checker..... 12 Silicon Chip Binders.................. 87 Silicon Chip Christmas PCBs... 75 Silicon Chip DCC Kits................ 99 Silicon Chip Shop.................76-77 Silicon Chip Subscriptions...... 100 The Loudspeaker Kit.com.......... 93 Tronixlabs.................................. 103 Wagner Electronics....................... 8 Errata and on-sale date PicoSDR, April 2026: the optional external TFT LCD screen should be the 2.8-inch type with the ILI9341 controller (Silicon Chip Cat SC3410), not the 3.5-inch type with an ILI9488 controller, as was specified in the parts list originally. Next Issue: the January 2027 issue is due on sale in newsagents by Tuesday, December 29th. Expect postal delivery of subscription copies in Australia between December 28th and January 13th. 104 Silicon Chip It can also be hard to find a distributor for these parts. None of our usual parts sources, including element14, RS, DigiKey and Mouser, seem to stock these CDIL BF469s. We can find some on eBay, but that is not a recommended place to source critical transistors for audio amplifiers! It’s rife with counterfeits. Without having some to test, we couldn’t say if they are any good. It’s possible they are fine, but we can’t recommend them just because they’re supposedly equivalent. We’re also concerned if there is only a single manufacturer making a specific part. They could discontinue production tomorrow, like many of the previous BF469 manufacturers did. Thus, we think the SOT-223 transistors Phil Prosser specified in the Calliope article, like the BF722, are the best alternatives available. They’re inexpensive, tested and known to work well. Their supply seems to be good, and they are easy to buy. One thing we should note is that while looking for a supplier for the CDIL BF469s, we discovered that element14 sells “Multicomp Pro” (their house brand) BF469s (Cat 4343315). Oddly, they list the Vceo rating as 50V, when a proper BF469 has a 250V rating. Another case of a part claiming to be something it isn’t? On the other hand, they claim an ft rating of 1.5GHz – impressive if true! Sourcing parts for an Ultra-LD Mk.4 Amp I’m looking at putting together a few of the Ultra-LD Mk4 Amplifiers (July-October 2015; siliconchip. au/Series/289). The HN3A51F and HN3C51F dual transistors used are no longer available. Is there an equivalent? Also, the NJL3281 and NJL1302DG Thermaltrak transistors, although not (yet) obsolete, seem to be somewhat out of stock in many places. Jaycar has them in stock at some stores, but they’re listed as “Clearance” on their website. On an unrelated subject, I’ve ordered two ADAU1467 Core boards through AliExpress to build the Digital Preamplifier and Crossover (October-­December 2025; siliconchip.au/Series/449). In both cases, I got ADAU1466 core boards. Talking to both AliExpress and to the shop has been an exercise Australia's electronics magazine in frustration. (K. J., Cleveland, Qld) ● The IMX8-7-F is a reasonable substitute for the HN3C51F dual NPN transistor used in the Ultra-LD Mk.4 amplifier, but unfortunately, there are no good alternatives to the PNP input pair (HN3A51F) with the same performance specifications and footprint. Happily, though, we still have some and can supply a small set of parts that includes both (siliconchip. au/Shop/7/3400). While the Thermaltrak transistors are becoming harder to buy, they work extremely well, and we don’t think it’s worth designing a new amplifier for a different transistor series until they are simply unavailable. If Jaycar runs out of stock, we suggest ordering from DigiKey, which still has reasonable stock levels for now: www.digikey.com.au/en/products/ detail/onsemi/1484399 www.digikey.com.au/en/products/ detail/onsemi/1484396 Regarding the ADAU1467 core boards, Phil Prosser responds: that’s unfortunate, they aren’t cheap! There are some significant differences in I/O between the ADAU1466 and ADAU1467. Without doing a lot of work, I can not say if you can make it work. You would definitely need to reprogram the ADAU chip using Sigma Studio, and I am worried that they won’t have sufficient I/O for the job. When ordering from AliExpress, you need to be really careful as sellers often combine multiple different items into the same listings, and you have to choose the right “colour” (which actually selects the model). Sometimes there’s a single item for sale, and we can provide a link, then the seller changes the listing to include multiple items, which is a real trap. Using ETI327 Hazard Flasher project at 6V Do I need to modify ETI project 327, “Turn and hazard indicator for your vehicle”, for use on a vehicle with a 6V electrical system? (K. W., Manly, Qld) ● The 555 ICs used for timing should operate at 6V without needing any changes to that part of the circuit. We suggest changing the base resistors for Q2 and Q3 from 2.2kW to 1kW to maintain a similar base current at 6V compared to the original design at 12V. Otherwise, we expect it will operate SC correctly with a 6V supply. siliconchip.com.au