Silicon ChipAdvanced Cable Analyser - December 2026 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: I seriously underestimated AI coding
  4. Feature: The History of AMD, Part 2 by Dr David Maddison, VK3DSM
  5. Project: Advanced Cable Analyser by Richard Palmer
  6. Project: Inrush Current Limiter by Phil Prosser
  7. Feature: Motor Control, Part 3 by Andrew Levido
  8. Project: NeoPixel RGB LED Analog Clock, Part 2 by Nicholas Vinen
  9. Feature: Working with AVR & PIC Fuses, Part 1 by Tim Blythman
  10. PartShop
  11. Project: The Magic Candle by Dr Hugo Holden
  12. Serviceman's Log: Working with switch-mode power supplies by Malcolm Batchelor et al
  13. Vintage Radio: STC Bantam model A141 by Ian Batty
  14. Subscriptions
  15. Market Centre
  16. Advertising Index
  17. Notes & Errata: PicoSDR, April 2026
  18. Outer Back Cover

This is only a preview of the December 2026 issue of Silicon Chip.

You can view 37 of the 104 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Articles in this series:
  • The History of AMD, Part 1 (November 2026)
  • The History of AMD, Part 2 (December 2026)
Items relevant to "Advanced Cable Analyser":
  • Advanced Cable Analyser main PCB [04101261] (AUD $5.00)
  • Advanced Cable Analyser lid PCB [04101262] (AUD $10.00)
  • Advanced Cable Analyser software and documentation (Free)
  • Advanced Cable Analyser PCB patterns (PDF download) [04101261-2] (Free)
  • Cutting/drilling diagrams for the Advanced Cable Analyser (Panel Artwork, Free)
Items relevant to "Inrush Current Limiter":
  • Inrush Current Limiter PCB [10110261] (AUD $7.50)
  • Inrush Current Limiter PCB pattern (PDF download) [10110261] (Free)
Articles in this series:
  • Motor Control, Part 1 (October 2026)
  • Motor Control, Part 2 (November 2026)
  • Motor Control, Part 3 (December 2026)
Items relevant to "NeoPixel RGB LED Analog Clock, Part 2":
  • BZ-121 miniature GNSS receiver (Component, AUD $30.00)
  • Neo-7M GPS module with onboard SMA connector & 5-pin header (Component, AUD $20.00)
  • VK2828U7G5LF TTL GPS/GLONASS/GALILEO module with antenna and cable (Component, AUD $25.00)
  • New RGB LED 'Analog' Clock kit (Component, AUD $85.00)
  • New RGB LED 'Analog' Clock firmware (Software, Free)
Articles in this series:
  • NeoPixel RGB LED Analog Clock, Part 1 (November 2026)
  • NeoPixel RGB LED Analog Clock, Part 2 (December 2026)
Items relevant to "The Magic Candle":
  • Magic Candle PCB [05112251] (AUD $2.50)
  • Magic Candle PCB pattern (PDF download) [05112251] (Free)
  • Magic Candle assembly diagrams (Panel Artwork, Free)

Purchase a printed copy of this issue for $15.00.

Advanced Cable Analyser by Richard Palmer Faulty cables are the bane of electronics and audio enthusiasts alike. While the most common faults result from wires parting company with connectors and shorts between pins, highresistance and intermittent connections can also cause havoc. E ven the most basic cable testers cost over $100 despite supporting a limited range of connector types – some you will use and possibly many that you will not. Accommodating all potential cable connectors is impossible in the limited space available on a reasonably sized case. Looking at audio connectors, while RCA connectors come in a single size, there are three-, four- and five-pin XLR connectors and even more DIN variations. There are three common sizes of TRS jacks with two, three or four pin variants. The list goes on. Rather than specifying which connectors should be used, in this project we have provided space on the sides and lid of the enclosure for constructors to select and lay out their preferred 30 Silicon Chip plugs and sockets. If you run out of space to mount less-often used connectors on the case, adaptor leads can be made and plugged into the onboard 8P8C connectors (often incorrectly called RJ45). Locating high-resistance connections is difficult with low-­ current testing, as small voltages are induced between the cable ends that are hard to measure accurately. This unit tests cables at 120mA, allowing cable resistances between 0.2W and 15W to be measured with reasonable accuracy. As each pin combination is tested for less than one millisecond, battery life is not unduly affected by the substantial test current. At the completion of the test cycle, a map of the cable, including bridged Australia's electronics magazine Features & Specifications ▶ Comprehensively analyses cables with up to eight wires ▶ Measures cable resistance ▶ Displays a cable map, including bridges between pins ▶ Results are visible in full sunlight ▶ Continuous test mode for intermittent faults ▶ Comparison against a reference cable ▶ A selection of test connectors ▶ USB or battery powered ▶ Test connector expansion port pins and cable resistance, appears on the display, then the unit switches off to conserve battery power. Since it’s an e-paper display, the image remains even when the electronics are powered off. Being reflective rather than backlit, it’s legible under a wide range of lighting conditions, including direct sunlight. Intermittent cable connections can be frustrating to trace. A long press on the start button puts the unit into continuous test mode, where all pin combinations are scanned ten times per second. If a substantial change in readings occurs, the unit stops scanning and shows the offending connection. Cables can also be tested against a known-good cable. Connecting the good cable followed by two long presses on the start button stores the reference configuration. Short presses make a comparison between the cable currently connected and the reference map, displaying any differences. When the unit’s USB cable is plugged into a computer, the connection maps are also sent to the computer in text format. Improving a traditional design Commercial cable testers generally connect LEDs to the pins on one connector and pass a current through each pin, lighting any LEDs where there is continuity with the other connector (Fig.1). The process is usually driven by a rotary switch or simple electronic sequencing of the test voltage. Any cable shorts or bridges between pins will light additional LEDs, but only when there is continuity to the driven pin. If there is no wire between the pins, either due to design or a poor connection, pin-to-pin bridges will not immediately be detected. siliconchip.com.au The open circuit will be detected, but the tester will not reveal all faults simultaneously. You would have to fix the open-circuit fault, then re-test the cable to find the short-circuit fault. Moderate cable resistances will not visibly dim the LEDs, so it is not possible to detect high-resistance connections with this method. To provide more information on cable resistance and pin-to-pin bridges, the common pole of the switch can be connected to a constant current sink (Fig.2) along with a low-value resistor on the high-side of each pin. If the current is known, the wire resistance can be calculated by measuring the voltage at each end of the cable and applying Ohm’s Law. A substantial test current helps to generate a measurable voltage drop even when the cable resistance is low. However, pin-to-pin bridges where there is no cable connection will still remain undetected. If a resistor of a substantially higher value than any expected cable resistance is connected between each pair of A and B pins (Fig.3), a small current will flow even when there is no cable connection. If there is no cable connection, the B-side pin will float high unless driven low. If there is an A-side bridge on an unconnected pin, the voltage on the A-side undriven pin will drop slightly with the driven A-side pin. For a B-side bridge, the undriven pin’s B voltage will also be pulled down. Where there is a B-side bridge and a cable connection to both pins, it is not possible to determine whether there is also an A-side bridge, as both the Fig.5: the TLC59108 functional block diagram. Source: Texas Instruments A pins will be at the same potential whether there is a bridge or not. This brings us to the final configuration for this project (Fig.4) where each A-side pin also has a switch. With this configuration, if the A-side switch for the driven pin is opened, the A-side voltage for any bridged pins and the driven pin will remain high. A mixture of bridged pins and crossed-over wires makes analysis more complex; the approach taken is explored below. TLC59108 LED driver This design is made simpler by using a specific IC, the TLC59108 constant current sink LED driver (Fig.5). It is designed to provide a controlled current sink for eight LED strings. It has a 20V maximum LED source voltage, allowing it to power up to eight LEDs in each string at programmable currents up to 120mA. Each string has an independent 8-bit pulse-width modulation (PWM) controller, operating at 97kHz, to control LED brightness. There is also a master controller that can dim or blink all the LED strings together. The PWM controllers can be disabled, allowing on/ off operation of each channel at a single, programmed current. The programmed maximum sink current is a combination of the current flowing through the external current programming resistor, REXT, and multiplier settings in one of the control registers. 256 different current values from 4mA to 120mA can be programmed. The chip is controlled over a twowire I2C serial bus and requires no external components other than resistor REXT. There is a sister chip, the TLC59108F, which does not offer the current programming facility; instead, it relies on a series resistor in the LED Figs.1-4: (1) common commercial cable testers comprise a battery, LED, series resistor and a switch pole for each connector pin. (2) Replacing the battery with a constant current source allows cable resistance to be calculated from the connector voltages using Ohm’s Law. (3) Adding a resistor with a value much higher than the cable resistance between connector pins enables bridged pins to be detected on the low side. (4) Adding high-side switches enables detection of high-side bridges when low-side bridges are also present. siliconchip.com.au Australia's electronics magazine December 2026  31 string. The F variant is not suitable for this project. Circuit details The full circuit is shown in Fig.6. The three main elements in the design are the test path, the controlling microprocessor and the display. Following the test path from the 3.3V rail, the A-side switches are implemented using P-channel Mosfets Q3-Q10. They were selected for their low on-resistance (<0.1W) and low gate-source threshold voltage (Vgs, -1.5V). Each Mosfet is controlled by an output from IC1, an eight-­channel 32 Silicon Chip PCA9554 (or PCA9554A) I2C bus expander, which provides individual control of each channel. The 10W high-side resistors lead to the A-side test connector, and the 150W resistors bridge to the B-side test connector. The values of the two resistors are compromises. The high-side resistor value needs to be high enough that there is a measurable voltage across it when there is a cable connection, yet low enough that the voltage across it is much less than 3.3V when the 120mA test current passes through it. The value of the bridging resistor Australia's electronics magazine needs to be substantially greater than any expected cable resistance, while still generating a measurable voltage across the high-side resistor for an open-circuit connection. The voltage across a 27.5W resistance will be 3.3V at 120mA. So, with 10W series resistors, the maximum measurable cable resistance is 17.5W. In practice, it is a little less, as the Mosfet and IC4 have a small series resistance and the 150W parallel resistors also draw a small current. The B-side pins are connected to the eight individually controllable constant current sinks of the TLC59108 siliconchip.com.au Scope 1: the yellow trace of the LED pin voltage shows the test and display cycle. The green 3.3V reference voltage is stable throughout. Fig.6: under the Pico’s control, Mosfets Q3-Q10 apply voltage to the pins of the connector at one end of the cable while the TLC59108 LED driver (IC4) sinks current via the pins at the other end. The voltages at each connector pin are sensed by the microcontroller’s A0 and A1 ADC pins via 8:1 analog multiplexers IC2 & IC3, which are sequenced in unison. LED driver (IC4). The TLC59108’s individual, group dimming and flashing capabilities are not required for this application; each channel is simply switched on or off at the programmed sink current. Only one channel is driven at a time. A pair of 8:1 analog multiplexers, IC2 and IC3, select the A and B connector pins to be measured by the microcontroller’s internal analog-to-digital converter (ADC). 74LV4051 and 74HC4051 chips both have an average series resistance of around 100W with a 3.3V supply, which varies by up to 100W across siliconchip.com.au their rail-to-rail input range. This does not cause any significant measurement error, as the resistance is much smaller than the Pico ADC’s 100kW input impedance. CD4051 multiplexers are not a good substitute, as their series resistance is five times higher at a 3.3V supply voltage. The choice of microcontroller came down to cost, ease of construction and programming. For ease of programming, the Raspberry Pi Pico 2 wins hands down as it can be programmed on any major computer platform without additional software or hardware. Australia's electronics magazine It costs only a few dollars more than a bare PIC or ATmega chip and already has the necessary ancillary components on board. Most of the processing is undertaken on CPU 0 of the RP2350 chip, with the buzzer beeps and LED flashing handled by CPU 1 so they don’t delay test and display processing. The Pico module has an onboard buck/boost switch-mode regulator that can generate 3.3V from a wide range of input voltages (1.8V to 5.5V). This allows significant flexibility in powering the unit from a battery or USB power. The Pico datasheet indicates that up to 300mA can be drawn from this supply, well in excess of the 150mA consumed when sinking a single channel at 120mA. The 3.3V supply is used as the test voltage as well as the ADC reference, automatically scaling voltage measurements if the test voltage varies. Scope 1 shows that the regulator copes well with the 120mA test current, with its output voltage varying by less than the 10mV switching noise. The Pico’s ADC has a nominally twelve-bit resolution. In practice, the accuracy is limited to around ten bits or 1024 (210) steps. A 3.3V reference voltage yields a step size of 3.2mV (3.3V ÷ 1024). when sinking 120mA, this step corresponds to a resistance resolution of 27.5mW. The three 1nF capacitors on the analog microcontroller inputs provide a low-impedance source for the ADC’s sample-and-hold circuitry as well as filtering out any high-frequency noise that may be present. The 8P8C connectors, CON6 & CON7, are in parallel with the A and B pin headers. As well as enabling the testing of network cables, they are a December 2026  33 convenient connection point for test harnesses. The e-paper display is controlled via a three-wire SPI serial interface, similar to that required by TFT displays. The additional BSY pin is polled by the Pico so that new commands or data are not sent while the display is updating. This is necessary as display update and erase cycles can take a second or two to complete. The piezo transducer is driven by a 50% duty cycle PWM signal from the GPIO9 digital output pin on the microcontroller via a 100nF capacitor. A passive device is used, as two different tones are required. The LED connected to digital output GPIO2 provides a visual indication of test progress. The Pico has an internal means of sensing when power is present at the USB connector. This signal determines several differences in operational behaviour between USB and battery power. The input voltage level is also read by ADC channel A2 via a voltage divider to estimate the remaining battery capacity if one is used. A key challenge in laying out the main PCB was minimising the resistance of the traces from the A-side Mosfets and source resistors to the A-side cable connectors and from the B-side connectors to IC4 to minimise resistance in the test path. To simplify construction and provide a decorative faceplate for the project, the enclosure’s lid is replaced by a second PCB on which switch S1, the display and LED are mounted, as well as some of the test connectors. Battery life As the cable tester is designed to be a toolbox item, it needs to be battery-­ powered, so its running time on a set of AA cells was a key design criterion. To reduce overall power consumption, we looked for components with low current requirements and sought to minimise the current drain while the unit was idling. The three main consumers of current in this design are the microcontroller, the display and the TLC59108 current sink. The multiplexers and bus expander draw minimal current. The Pico 2 consumes 18mA when running at 150MHz, 9mA at 50MHz and 2mA when in sleep mode. As the computing power of the Pico is well in excess of our needs, it runs at 50MHz to minimise its operating current. While putting the microcontroller to sleep would have provided an additional benefit, the options available are not sufficiently flexible to make this attractive. For TFT displays, the backlight LED can consume up to 40mA at full intensity, which can be reduced by dimming the LED using a PWM signal. Small OLED displays average around 20mA. E-paper displays, o nce updated, consume no current. As retaining the display as long as Photo 1: I mounted RCA, barrel, banana and XLR sockets on my unit but you could use a different combination. 34 Silicon Chip is needed to identify and rectify any cable faults is a useful feature, e-paper becomes an obvious display choice. The TLC59108 current sink (IC4) draws nearly 30mA of idle current. Even in its lowest power mode, when reset is held low, the chip consumes only 2mA less. This is not particularly significant when driving eight LED strings at 120mA each, but it is more than an acceptable constant battery drain for extended idle use. As alternative approaches for creating the current sink and low-side switching functions added significant cost or circuit complexity, we sought to reduce its average power consumption. Instead of dealing with the microcontroller and IC4’s idle currents separately, we switch off power to the entire circuit at the end of each test and display cycle using P-channel Mosfet Q1. The reverse leakage current of D1 and the off-state current of Q2 are both in the nanoampere range. A battery power switch (S2) is also provided to prevent accidental toolbox triggering. Tests run in single-shot mode; this is a very effective strategy, as the active cycle is only a few seconds long. For continuous and comparison modes, a reference cable map needs to be stored between test cycles, and the current sink IC needs to remain active, so the available power savings are limited. USB power is advised when undertaking cable test sessions that use these modes for an extended period. The minimum voltage at which the unit will function properly is primarily determined by the battery discharge curve. Alkaline cells are 90% discharged at 1V. The Pico’s onboard regulator is specified to operate from as low as 1.8V, and Q1 was selected to switch on fully with a similar Vgs. To provide some headroom for the regulator and Q1, the unit shows 0% battery remaining and switches off with a battery voltage just below 3V. Thus, a three-cell alkaline battery is ideal. AAA alkaline cells will deliver around 1000mAh when discharged to 1V, which should allow many hundreds of five-second test cycles at an average 50mA current (see siliconchip. au/link/accr). The test cycle When the start button (S1) is depressed, P-channel Mosfet Q1 conducts, connecting the battery to the rest Australia's electronics magazine siliconchip.com.au of the circuit. Once the microcontroller has booted, PWR goes high, sustaining power by switching on NPN transistor Q2 until the signal is released after the completion of the testing cycle, switching off Q1 and shutting everything down. The Pico’s GP12 pin has its internal pull-up resistor enabled, so the input is normally high when the microcontroller is powered on. The pull-up resistor also provides bias to S1 once PWR has been pulled low. Diode D1 ensures that PWR and START are isolated so that S1 can still be sensed when PWR is low. The test current is passed through P-channel Mosfets Q3-Q10 and the 10W resistors on the high side, through the cable being tested, to a channel on the TLC59108 constant current sink (IC4). During testing, IC4’s pins and the Mosfets are enabled as required, and the voltages at each of the A and B pins are selected by multiplexers IC2 and IC3 for measurement at the ADC pins on the microcontroller. While the two multiplexers have separate channel select pins on the microcontroller, in practice they are always sequenced together. Mosfets Q3-Q10 conduct when their gates are pulled low by IC1. In single-shot mode, IC4’s outputs are enabled in sequence at their 120mA maximum current setting, with all A-side Mosfets enabled. At each step, the multiplexers cycle together through each channel, and the A and B voltages are read. The driven channel A-side Mosfet is switched off and a second pair of readings taken. Over the 30ms test cycle, a total of 256 measurements are stored for later analysis. In most cases, only the readings with all the A-side Mosfets enabled are required for analysis. If Va is close to 3.3V and Vb is low when the corresponding B pin is driven, the connection is open. For a pair of connected pins, Va and Vb will be close in value. The resistance is calculated by applying Ohm’s Law to the voltage difference, as the current is known. A cable map entry is created for each pair of connected pins, flagged with a “C” (for connected) and the resistance recorded if it is greater than 0.2W. If the resistance is more than 15W, an open circuit is assumed. Crossed wires and multiple connections are detected and logged. siliconchip.com.au Parts List – Advanced Cable Analyser 1 double-sided 80 × 62mm green PCB (main) coded 04101261 1 double-sided 89 × 152mm blue PCB (lid) coded 04101262 1 Raspberry Pico 2 microcontroller module with header pins 1 1.54-inch 200 × 200-pixel Waveshare monochrome e-paper display with cable [Core Electronics WS-12955] 1 8-pin 0.1-inch/2.54mm header for display (CON4) [Core CE08367] 2 8P8C PCB-mount sockets without LEDs (CON6, CON7) [Amphenol 54602908LF, Oupiin 8949-F188-06BNA, Altronics P1438, Core PRT-00643] ● 2 20-pin 0.1-inch/2.54mm header sockets for Pico 2 [Core CE09119] 1 3V passive piezo transducer (PB1) [Altronics S6109, Jaycar AB3442, Core ADA1740] 1 12mm tactile switch with 3.5mm or higher round stalk (S1) [Jaycar SP0609, Core COM-12993] 1 miniature slide switch (S2) [Altronics S2010, Jaycar SS0852, Core CE03160] 1 3×AAA flat battery holder (BAT1) [Altronics S5040, Jaycar PH9272, Core FIT0626] 3 AAA alkaline cells 1 micro USB Type-B to Type-A cable (for programming and USB operation) multiple pairs of test connectors (constructor’s choice) various colours of hook-up wire (lengths vary with connector choices) ● Jaycar PS1478 is not suitable Semiconductors 1 PCA9554(A)D I2C bus expander or TCA equivalents, SOIC-16W (IC1) [Mouser 595-PCA9544ADWR] 2 74HC4051 or 74LV4051 8:1 analog multiplexer ICs, SOIC-16 (IC2, IC3) 1 TLC59108IPWR (not F variant) constant-current LED driver, TSSOP-20 (IC4) [Mouser 595-TLC59108IPWR] 9 AO3401(A) P-channel Mosfets or similar, SOT-23 (Q1, Q3-Q10) [Core COM-29463, Mouser DMP1045U-7] 1 BC817 or similar NPN transistor, SOT-23 (Q2) 1 3mm red LED, bezel optional (LED1) [Altronics Z0200, Jaycar SL2615] 1 BAV70 or similar dual common-cathode signal diode, SOT-23 (D1) [Altronics Y0099] Hardware 1 UB1 Jiffy box 3 M3 × 15mm tapped male/female spacers with nuts 3 M3 × 6mm countersunk head machine screws 2 M2 × 6mm panhead machine screws [Altronics H3101, Jaycar HP0390] 4 8mm clear round rubber bumpers [Bunnings] 1 8cm length of double-sided mounting tape Capacitors (all SMD 2012/0805 X7R or X5R 50V SMD ceramic) 3 1μF 5 100nF 3 1nF Resistors (all SMD 2012/0805 ⅛W ±1% unless noted) 1 100kW 3 3.3kW 1 33kW 9 150W 1 22kW 8 10W SMD M3225/1210 or M3216/1206 ¼W ±1% SMD 3 10kW [Altronics R7972] Bridge detection follows. There are several different cases for bridged pins: A- or B-side bridges, where the A and B pin pairs are connected or not connected. Each requires specific treatment. Where there is a cable connection from any A-side pin to the driven B-side pin, any non-driven pin developing a significant voltage across its Australia's electronics magazine 10W resistor it is flagged as having an A-side bridge to the connected A-side driven pin. A B-side bridge will cause a much smaller voltage to be created across the 10W resistor, which is ignored. If the bridge is on the B-side, Vb on the bridged, the undriven pin will also fall and be flagged with a “B”. Where there is no cable connection December 2026  35 to the driven pin, an A-side bridge will cause a smaller drop in Va for each of the bridged pins. If the bridge is on the B-side, Va for the bridged pins will drop when either B-side pin is driven. These are also flagged with a “B”. Where there are both A-side and B-side bridges on the same pin pairs, the second set of readings, with the A-side Mosfet open, come into play. If the process above finds a B-side bridge for a pair of pins, if the alternative Va is high, the pair is marked as an A-side bridge, but only if the reversed pair of pin numbers has already been flagged as a B-side bridge. Where there is a bridge between two connected pins, there’s no electronic means of discovering which end of a low-resistance cable has the bridge. In this case, both A and B side bridges are electrically identical. The unit may flag these cases as crossover connections or B-side bridges. In the rare case that the unit detects a connection and cannot determine the type, it displays a dotted line bridge on the B side and marks the value with a “?” plus the two pin numbers on the right-hand side of the display. In both these cases, the eyeball is the best test instrument to make the final determination. The resulting cable map is displayed, with resistances greater than 1W shown as dotted lines. At the end of the cycle, the unit switches off to save power, leaving the cable map displayed. If the latest test cycle found no connections or bridges, the display is cleared. In continuous mode, the cable map from the first cycle is saved, and the maps from subsequent cycles are compared to it. If a difference is found – a missing, extra, or higher resistance connection or bridge – testing ceases and only the difference is displayed on the screen. The type of difference, a missing or extra connection, is noted on the bottom line of the display. In comparison mode, the initial cable map is stored as a reference, and the unit makes one comparison scan for each short button press. Results are displayed as for continuous mode. If there has been no activity for one minute, the unit flashes the LED and beeps once as a reminder that it is still switched on. Construction The Advanced Cable Analyser is built on a double-sided PCB that measures 80 × 62mm and is coded 04101261. The lid is also a PCB, coded 04101262, measuring 89 × 152mm. The PCB mounts on 15mm-long tapped spacers with the component side down in the bottom-right corner of the Jiffy box so that the 8P8C and Pico USB connectors can be accessed from outside the case. The screws through the bottom of the box should be countersunk to avoid bumps in the instruction card. The box is much larger than the PCB to allow for cable connectors to be mounted on the sides, top and lid. The display, battery holder, power and start switches will be mounted on the underside of the lid. A pin header is used to connect the e-paper display as it comes with a suitable cable. The rest of the off-board wiring (S1, buzzer and battery) is soldered directly to the PCB. The Pico is mounted on header sockets. Before mounting any components on the main PCB, pare off the vertical ribs in the case next to where the Pico’s USB connector will lie with a chisel or sharp knife. There is adequate clearance on the bottom edge of the case with the PCB ribs left in place, as the 8P8C sockets protrude 5mm past the edge of the PCB. Place the blank PCB component-side down in the bottom right corner of the case, then mark and drill the 3mm mounting holes for it – see Photo 3. Now refer to the PCB overlay diagram, Fig.7, to see which components go where on both sides of the board. On the main PCB, mount the SMD parts on the Pico side first, followed by the 19 that are on the opposite side of the board, including one more IC and one transistor. Various techniques can be used, including hand-soldering, hot air reflow, oven reflow, or hotplate reflow (probably only suitable for parts on one side, though). Hand-soldering with a standard temperature-controlled soldering iron is possible as long as you use a good-quality flux paste. We Photos 2 & 3: the bare PCB is used to mark the mounting holes in the case. The ribs next to the Pico have been pared off to allow access to the USB connector. Only the headers for the display are required; the wires for the battery, buzzer, LED and switch connections can be soldered directly to the PCB pads. 36 Silicon Chip siliconchip.com.au Fig.7: fit the components to both sides of the board like this. We’re showing pin headers for CON1-CON5, which could have DuPont wires plugged into them, but you could also solder wires directly to the pads (except CON4). Don’t use headers for CON8 and CON9; it’s better to solder those wires directly to avoid extra resistance in the measurements. recommend having some solder-wicking braid and flux cleaner (eg, pure alcohol) on hand, plus fine-tipped tweezers. Even with hand-soldering, there are various techniques that can be used. You would usually start by placing an IC in its correct orientation, tacking one pin, then verifying that all its other pins are centred on their pads. If not, remelt that initial solder joint and gently nudge it into position. Repeat until you are happy, then add flux paste to all the pins. One option is then to add some solder to the clean tip and drag it along one edge of the IC (not the one with the tacked pin!) so that solder flows onto all the pins and pads, aided by the flux paste. Another is to add a small amount of solder to the clean tip and touch it to the end of one pin, observing that solder flows onto the pin and pad, then repeating that for the other pins. Once all pins of an IC have been soldered, check under magnification for solder bridges between them, or for any joints where solder has not flowed properly onto both the pin and the pad. If you find any, add a little extra flux paste to the pin(s) and reflow them. If that doesn’t fix it, apply braid to the effected pin(s), press down with the soldering iron and slide it away after a few seconds. The TLC59108 chip has closely spaced pins and you probably won’t be able to avoid bridging them but luckily it’s quite easy to clean them up with some extra flux paste and solder wick. Just be careful not to pull the wick too hard until the excess solder has melted siliconchip.com.au and flowed into it, at which point it’ll be easy to slide away from the pins. When all the solder joints on a chip look good, clean off the flux residue and proceed to the next one. Other SMD parts like transistors, diodes, resistors and capacitors can be soldered similarly; they just have fewer pins. Next, solder in the pin sockets for the Pi Pico 2, followed by the 8P8C sockets on the top of the PCB, and the 8-pin display header on the underside. After that, add the rest of the components on both sides of the PCB. Mark the positions of the 8P8C connectors on the bottom right of the case using Fig.8 and drill 6mm holes. Position the PCB on its spacers and with the Pico removed, enlarge the 8P8C connector holes with a file. Mount the Pico and repeat for the USB connector, using Fig.9 as a guide. Start enlarging the hole from the 8P8C end, as the connector will move slightly toward that end once the hole is completed. There is no need to leave extra space around the USB connector, as a standard USB-micro plug is long enough to connect properly through the side of the case. Fig.8: make the openings for the 8P8C connectors by drilling 6mm pilot holes and enlarging them with a file. These diagrams are views from the outside of the case. Fig.9: after the 8P8C openings have been made, mount the Pico and position the USB connector hole. Drill a 2mm hole and enlarge it with a file. Australia's electronics magazine December 2026  37 Before mounting the Pico 2 module on the PCB, load the firmware, which you can download from siliconchip. au/Shop/6/3646 Hold down the white button on the top of the Pico while plugging it into a USB port on your computer and copy the firmware onto the RP2350 drive that should appear on your computer’s file explorer or equivalent. Once that completes successfully, disconnect the Pico from the computer and plug it into the PCB. Connect the e-paper display cable to CON3 on the underside of the main PCB (see Table 1). The Waveshare module comes with flying leads terminated in female DuPont connectors. Testing Reconnect the USB cable to the computer and the e-paper display should show a welcome message after a few moments. Its black border can be used to align the display when it is mounted on the underside of the lid (see Photo 4). If you have a USB power monitor, the standing current should be around 35mA when powered via USB. Once the connections have been validated, a light run of hot glue across the DuPont connectors will convert them into a more secure block. Ensure that no glue gets into the metal parts of the connectors by aligning all the locking tabs on one side and gluing the other. On the prototype, the heat from a second gluing run along the latch side Table 1: Waveshare 1.54-inch e-paper connections PCB Signal Colour 1 Vcc Grey 2 CS Orange 3 GND Brown 4 SCK Yellow 5 TX Blue 6 DC Green 7 RST White 8 BSY Purple of the connectors caused all the plastic locking tabs to deform, requiring a final run of hot glue along the top of the connector to secure the pins. Try to avoid that! You could also superglue them together. With the unit connected to USB power, briefly short the pins of the start connector, CON2. The display should flash several times and then clear. If a cable map is displayed with connections or bridges, check for solder bridges between the pins on the three ICs. Further assembly Before mounting the tactile switch, LED and e-paper display, lay out and make the holes for any connectors you want on the lid for testing cables. Refer to the photos of my prototype for ideas. To assist, a grid has been printed on the underside of the lid PCB. The PCB and display take up the bottom 65mm of the case. Any space above that is free for test connectors. A-side connectors should go on the left-hand side of the layout, to match the cable map on the display and the 8P8C connectors. The lid that came with the case can be used for testing your connector layout, as it is surplus to the project’s needs. If your LED has a chrome bezel, drill out the hole in the lid to 6mm. Remove the e-paper’s mounting screws, spacers and screen protection film. Position the display over the square cut-out in the lid PCB with the connector end toward the bottom of the case. Bend four 1cm lengths of solid hook-up wire into L shapes, then mount the display temporarily with a strip of electrical or masking tape across its back (Photo 5). The connector on the display goes toward the bottom of the case. As mentioned earlier, there is a border on the splash screen to aid alignment. When you are satisfied with its position, thread in each of the mounting wires and solder them to both the PCB and mounting holes on the display, re-checking alignment after each wire is soldered. Trim the mounting wires close to the display. Carefully bend the pins on the tactile switch so they are facing towards the button – see Photo 6. If needed, bend the ends back down so that they are flush with the top face of the switch. Tape the switch temporarily Photo 4: the splash screen has a border that is useful for aligning the display in the lid cut-out. Photo 5: the display and start switch taped in place on the underside of the lid, ready for soldering. Photo 6 (inset): the pins on the tactile switch need to be bent upward so it can be mounted on the back of the lid PCB. 38 Silicon Chip Australia's electronics magazine siliconchip.com.au in place, checking the clearance of the central button after each pin is soldered. Solder two 15cm lengths of flexible hook-up wire to the switch pads. Mount the LED with 15cm flying leads connecting to the main PCB. Hot glue will secure a standard LED. The power switch mounts on the back of the lid PCB using 2mm screws. The battery box is secured to the underside of the lid with two strips of double-sided mounting tape. Careful positioning of the battery holder is required, as it needs to avoid the box’s mounting pillar at one end and the display connector on the PCB at the other. The wires can point in either direction. The red wire goes to the switch and the black wire directly to the negative terminal of CON1 on the main PCB. Another length of hook-up wire connects the switch to the positive terminal of CON1. The LED wires connect to CON3 on the underside of the main PCB. Connect the two flying leads from the start switch to CON9, also on the underside; similarly, the buzzer connects to CON5. Polarity does not matter for the start switch and buzzer. The buzzer is mounted on the side of the case next to the PCB – it can be secured with a touch of superglue. Once the test connectors are mounted, wire all the pin 1s on the A-side connectors together in a daisy chain, leaving a 10cm tail on the closest connector to the PCB. Solder the Table 2: Operation summary Operation Start Stop Single shot Short press Automatic Continuous mode Long press Automatic on detection of difference and power off Comparison Two long presses, short press for each test Long press Clear screen Short press with no connections Automatic tail to CON8’s pin 1 and repeat for the other pins on the A and B connectors. Recheck for shorts between pins by running a test cycle with no cables connected. Print the instruction card and trim it on the grey border, rounding the corners. Laminate the card and trim with a 2mm clear border and rounded corners. After mounting the PCB, stick it to the bottom of the case with double-­sided tape and place the rubber bumpers in the corners (see the photo below). Operation Table 2 outlines the unit’s basic operation. Plug in a cable to be tested – a short press on the start button will initiate the testing cycle. One beep indicates that a single test cycle is being performed. When complete, the number of connected pins and bridges are displayed, as well as a resistance estimate of paths with a resistance greater than 0.2W. Paths greater than 1W have dashed lines. Connection resistances greater than 15W are considered as open circuit – see Photo 7 & Screen 1. The unit switches off at the end of each cycle to minimise battery drain while the cable map remains visible on the e-paper screen. Clearing the display is recommended at the end of each session to prevent image ghosting. A short press with no cable connected will do the trick. High-pitched beeps are emitted during each test cycle. Low-pitched beeps signal a change in the unit’s state: powering on or off, a mode change, the sixty-second no-activity alarm, clearing the display, or switching off. The LED generally flashes along with the beep. To test for intermittent connections, continuous mode is initiated with a long press of the button. After two beeps, the first scan is saved as a reference and compared with scans taken ten times a second. The LED flashes Photo 7: a test rig with resistors connecting between pins 1-7. The resistances are 0.22W for pin 1, followed by 1.2W, 2.2W, 3.3W, 10W, 22W and 33W on pin 7. siliconchip.com.au Australia's electronics magazine December 2026  39 Screen 1: the cable map displayed for the Photo 7 test connections via the 8P8C sockets. The 33W path registers as an open circuit. Screen 2: a test with an A-side 1-2 bridge on connected pin 1, a B-side 3-4 bridge with no cable connection, both A & B bridges on 5-6 with no cable connection and A & B bridges on 7-8 with a connection on pin 7. Screen 3: a long network crossover cable produces a more complex cable map. Screen 4: in comparison and continuous modes, only the differences from the reference cable map are shown on the screen. Screen 5: the serial terminal display for Screen 2 above. Screen 6: the serial terminal display for Screen 3 above. Another long press exits comparison mode, clears the display and switches the unit off. If a substantial number of cables are to be tested, consider powering the unit via the USB cable. The remaining battery capacity is shown in the bottom-left corner of the display. If the battery voltage falls below 3V, it automatically clears the display and switches off. After each minute of inactivity, the unit will beep and flash the LED as a reminder that power is still being drawn. Even though the circuit draws less than one microampere after it automatically goes off, switching the unit off using the power switch will prevent accidental triggering. The unit may be powered via the Pico’s USB port, in which case it does not switch off between runs as Q1 is not in circuit. The battery switch should be in the off position when the unit is USB-powered to avoid shorting the battery to the USB supply, which could be bad for both. When connected to a computer via the USB port, the unit sends the cable map and other test information to a terminal program such as Arduino’s Serial Monitor or PuTTY at 19,200 baud in N81 serial format. The format of the cable map is suitable for importing into a spreadsheet: a header with the field labels followed by the cable map items. “C” denotes a connected pin, while “A” and “B” indicate bridges on the respective connectors. Lower-case letters indicate missing or extra connections in comparison or continuous modes. rapidly, once for each scan. If a difference is found, the unit switches off with the first difference displayed. The bottom line of the display provides an indication of whether the difference is an extra or missing connection. A short press cancels continuous testing and switches the unit off. To allow multiple cables to be tested against a single reference, plug in the reference cable and use two long presses on the button to save the reference map and cause the unit to enter comparison mode. It will then display the reference cable map. Each short press then compares the current cable with the reference, and the first encountered difference (two beeps) or an OK message (one beep) is displayed. A long press clears the display and switches off. Comparison mode does not switch off between runs; the 35mA idle current will drain the battery if the unit is left switched on for long periods. 40 Silicon Chip Australia's electronics magazine Conclusion Faulty cables should cause a little less pain with this cable analyser, which can do much more than simple go/no-go testing. A bonus is that the constructor gets to choose the connectors that they most commonly use, and the 8P8C sockets are available to create simple and easy plug-in adaptors for less-used SC connectors. siliconchip.com.au