Silicon ChipThe Magic Candle - December 2026 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: I seriously underestimated AI coding
  4. Feature: The History of AMD, Part 2 by Dr David Maddison, VK3DSM
  5. Project: Advanced Cable Analyser by Richard Palmer
  6. Project: Inrush Current Limiter by Phil Prosser
  7. Feature: Motor Control, Part 3 by Andrew Levido
  8. Project: NeoPixel RGB LED Analog Clock, Part 2 by Nicholas Vinen
  9. Feature: Working with AVR & PIC Fuses, Part 1 by Tim Blythman
  10. PartShop
  11. Project: The Magic Candle by Dr Hugo Holden
  12. Serviceman's Log: Working with switch-mode power supplies by Malcolm Batchelor et al
  13. Vintage Radio: STC Bantam model A141 by Ian Batty
  14. Subscriptions
  15. Market Centre
  16. Advertising Index
  17. Notes & Errata: PicoSDR, April 2026
  18. Outer Back Cover

This is only a preview of the December 2026 issue of Silicon Chip.

You can view 37 of the 104 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Articles in this series:
  • The History of AMD, Part 1 (November 2026)
  • The History of AMD, Part 2 (December 2026)
Items relevant to "Advanced Cable Analyser":
  • Advanced Cable Analyser main PCB [04101261] (AUD $5.00)
  • Advanced Cable Analyser lid PCB [04101262] (AUD $10.00)
  • Advanced Cable Analyser software and documentation (Free)
  • Advanced Cable Analyser PCB patterns (PDF download) [04101261-2] (Free)
  • Cutting/drilling diagrams for the Advanced Cable Analyser (Panel Artwork, Free)
Items relevant to "Inrush Current Limiter":
  • Inrush Current Limiter PCB [10110261] (AUD $7.50)
  • Inrush Current Limiter PCB pattern (PDF download) [10110261] (Free)
Articles in this series:
  • Motor Control, Part 1 (October 2026)
  • Motor Control, Part 2 (November 2026)
  • Motor Control, Part 3 (December 2026)
Items relevant to "NeoPixel RGB LED Analog Clock, Part 2":
  • BZ-121 miniature GNSS receiver (Component, AUD $30.00)
  • Neo-7M GPS module with onboard SMA connector & 5-pin header (Component, AUD $20.00)
  • VK2828U7G5LF TTL GPS/GLONASS/GALILEO module with antenna and cable (Component, AUD $25.00)
  • New RGB LED 'Analog' Clock kit (Component, AUD $85.00)
  • New RGB LED 'Analog' Clock firmware (Software, Free)
Articles in this series:
  • NeoPixel RGB LED Analog Clock, Part 1 (November 2026)
  • NeoPixel RGB LED Analog Clock, Part 2 (December 2026)
Items relevant to "The Magic Candle":
  • Magic Candle PCB [05112251] (AUD $2.50)
  • Magic Candle PCB pattern (PDF download) [05112251] (Free)
  • Magic Candle assembly diagrams (Panel Artwork, Free)

Purchase a printed copy of this issue for $15.00.

Dr Hugo Holden’s Magic Candle Impress your friends and family with an electric lamp that you light like a candle – with a flame from a match or a lighter – and blow out with your breath! A fter the invention of the transistor at Bell Labs in 1948, many portable battery-­ powered projects became possible that were previously impractical using valves. Various projects appeared in hobby magazines in the 1950s to 1970s using transistors in different roles. One such project used a small light bulb to simulate a candle. You could activate it with a burning match or cigarette lighter held near the lamp, then blow it out (switch it off) with your breath, just like blowing out a candle! I attempted to make one of these in the early 1970s, but the design was not ideal and it didn’t work properly. I thought it would be fun to revisit this idea. Rather than trying to make it look exactly like a candle, it could instead be a lamp used to provide a romantic light source at a dinner engagement. The colour temperature and intensity of the lamp would provide similar illumination and colour temperature to a single candle. Importantly, it could be lit using a match or lighter, then later blown out, just like a candle. This would mean it wouldn’t need any external on/off switch, although I 78 Silicon Chip wanted to have a way to switch it on or off without using a flame if necessary (more on that later). You can see a video of the Magic Candle in operation at www.youtube.com/shorts/ yPeLhmbzurw After using it a few times, my wife suggested it could be improved by placing a diffuser (lampshade) over the bulb. So I added a collar on the upper part of the structure, 30mm from the top, to support a removable light diffuser made from some translucent acrylic tube that was 80mm tall. This worked very well, as shown in Photos 1 & 2. The tube needs to be slipped off to light the candle with the match, but with the tube present, it is just as easy to blow the candle out as before. Design basics I decided on negative temperature-­ coefficient resistors (NTC thermistors) for temperature sensing, rather than a thermocouple or IC-type sensor using a P-N junction. NTC thermistors are inexpensive and very small. They have a large change in output voltage per °C with a simple series resistor; their lack of linearity doesn’t matter in this case. Australia's electronics magazine I decided on three C cells as the power source to keep the size reasonable while still providing a long battery life. AA cells are too low in capacity for the task, while D cells are too large. Keep in mind that we’re using an incandescent lamp, rather than a more modern LED, because its light is more pleasing and relaxing, similar to a candle. This is because, in essence, a candle is incandescent. They both emit continuous light spectra. A candle burns yellow due to the incandescence of burning carbon particles (soot) in the wax. A wax candle generally has a light output equivalent to a 5-7W incandescent bulb, so I elected to use a 6V, 5W automotive filament lamp, running from an average voltage of around 4V. This gives a 2.2W lamp with a similar colour temperature to a candle; I found that was plenty of light output for the task. The light emitted is a little whiter than a candle with fresh cells, but still (just) usable with a more orange colour down to 1V per cell. Using good alkaline cells, the lamp will run for around 10 hours total before needing to be replaced. The device is 25cm tall with a 33mm diameter above the base. C cells have close to a one-inch (25.4mm) diameter, so they fit easily into the 30mm inner diameter tube. Conveniently, Bunnings carries a suitable white plastic pressure pipe, made by Holman and said to be a “25mm nominal pressure pipe” (PVP2512-1). The pipe I bought was just a little ovoid, but it was still a good press fit into 33mm holes I cut in the base rings with a standard 33mm hole cutter tool, which cuts the hole a little oversized. So that you can leave the cells in the lamp between uses without them going flat, the Magic Candle’s power consumption needs to be near zero when not in use. This is a little tricky given that I didn’t want it to have a mechanical on/off switch. The measured current consumption when not in use is a mere 4nA, so the cells will last for their shelf life. I also had to consider the supply voltage; it would start over 4.5V with fresh cells, but the lamp is still usable down to about 2V. So the control electronics would need to work over that range. This created some interesting design challenges; I managed to make siliconchip.com.au Photos 1 & 2: the shade is optional. It helps to diffuse the light, but you have to take it off to ‘light’ the Magic Candle. it work down to around 2.2V, which I thought was adequate. The thermal sensor In this design, the thermistor temperature sensors are inside a hollow brass tube that is close to 3.175mm in outer diameter, 34mm long, with a wall thickness of about 0.35mm – see Photo 3. The brass tube dominates the thermodynamic properties of the sensor because the mass of the brass, its heat capacity, and its surface area. So, if the tube is heated 10°C above ambient temperature, how long might it take to cool back down? Objects gain or lose heat by radiation, conduction and convection. For small objects that are not extremely hot, convection tends to dominate. Radiation is a weak mechanism of heat loss unless the object is very hot or very big. Newton’s law of cooling says that an object cools in an exponential decay, ie, dT/dt = -k(T – Tenv), where dT/dt is the change in temperature with time, T is the current temperature and Tenv is the ambient temperature. The decay constant, k, can be found by experimentation or estimated as k = hA ÷ mc, where A is the surface area, m the mass, c the specific heat capacity of the material and h the ‘convective heat transfer coefficient’. h depends on the geometry of the object, its orientation, air or fluid convection and surface air speed. In free air, h typically varies between 5W/m2K and 25/m2K. The cooling time constant, TC, to decay to by 63% is 1/k. So after 3TC, it would have cooled down 95% of the way toward ambient temperature. siliconchip.com.au For a small tube cooling in air, we can assume an h value of around 10. For the brass tube used here, the constants are m = 0.000914kg, c = 380J/ kgK and A = 0.000355m2, making k = 0.0102. So the ‘cooling time constant’ (somewhat analogous to the time constant for a capacitor to discharge to 37% of its initial value) is 98 seconds (1 ÷ 0.0102). Thus, in 3 × 98 seconds or about five minutes, after heating by 10°C, it will be within about 0.5°C of ambient temperature. So there is moderate thermal inertia in the small brass tube, much more than the thermistors, which have a thermal time constant of about 7-10 seconds. But you cannot just place the fragile thermistors in the space by the lamp; they must have some form of mechanical protection and support. Clearly, a differential temperature sensor is required. It must detect a small change in temperature and still work over a wide range of ambient temperatures. So, if we can detect a temperature rise at the exposed end of the tube compared to the lower portion, Fig.1: by placing the two NTC thermistors in a resistor bridge, the comparator (IC2d) responds to the difference in temperature between them. The different-value fixed resistors add a fixed offset so that the comparator doesn’t trigger until one thermistor is a few degrees hotter than the other. we should be able to detect if a match or lighter is lit near it. The thermistors are in a differential bridge arrangement to decrease the response time in detecting heating, and to shorten the recovery time after the sensor tube has been significantly heated. Thermistors NTC1 and NTC2 are wired into a bridge circuit, feeding an op amp that’s used as a comparator with a small amount of hysteresis (see Fig.1). When the comparator output goes positive, the lamp is activated and is held on by an S-R flip-flop. The 5kW thermistors used (RS 151221) have a sensitivity of around -4% per °C at 25°C, indicating a ‘B value’ of about 3640. So a change of +1°C would drop the 5kW resistance by around 200W near room temperature. A plot of resistance versus temperature for an NTC thermistor has a familiar exponential decay format, and the tangent to the graph, representing a change in resistance with a change in temperature, decreases with increasing temperature – see Fig.2 overleaf. Photo 3: the two NTC thermistors are placed 25mm apart in this brass tube. Australia's electronics magazine December 2026  79 Fig.2: this shows how the resistance of an NTC thermistor varies with its temperature. The relationship is welldefined but nonlinear. Fig.3: forming a voltage divider with an NTC thermistor and a fixed resistor gives this sort of voltage output. When a resistor is added to make a divider, the result is an S-shaped curve, as shown in Fig.3. The output of the bridge is related to the difference between the two thermistor’s temperatures, and the types of thermistors I used are designed to have matched curves, which helps to balance the bridge. The bridge circuit works effectively over the full voltage range (2.2-4.8V) and a wide temperature range. It does not require that the voltage or current supply to the bridge is stabilised or regulated. I found it was not necessary to compensate for the non-linearity, or the effects of lowering battery voltage. The offset voltage due to the 1% tolerances of the 4.3kW and 4.7kW resistors is much higher than the op amp’s input voltage offset. 80 Silicon Chip Another advantage of the bridge arrangement is the tiny amount of self-heating of the thermistors due to their operating currents largely cancelling out. The different values of the 4.3kW and 4.7kW resistors in the voltage dividers set up a 180mV offset with new cells (about half that with discharged cells), which corresponds to an approximate 2°C offset at 25°C. This offset keeps the comparator output negative unless there is a transient temperature gradient, with NTC2 being hotter than NTC1. That causes the comparator output to go positive. The offset of 2°C is high enough to eliminate noise and ambient temperature change effects, but low enough that the response time is fast once a flame is held in proximity to the brass tube holding the thermistors. After the flame is removed, which is the natural response after the lamp lights, the brass tube and sensor temperatures settle to a fairly uniform temperature along the tube length. The comparator output then returns negative. The tube cools back down to near ambient temperature over some minutes, but due to the offset voltage, the comparator output is low the whole time. Even though the brass tube takes around 98 seconds to lose 63% of the acquired temperature increase, the sensor system becomes re-­operational much more quickly because of the bridge arrangement. On examining the comparator output after the match is removed, the heat in the brass tube reaches equilibrium in 8-10 seconds (similar to the thermal delay time between the two sensors). Both the sensors reach similar resistance values, and the output of the comparator goes low. At that point, another match can be used to light the lamp. In the circuit diagram (Fig.4), the output from the heat sensor comparator is AC-coupled, with a one-­second time constant, to the S-R flip-flop that controls the lamp’s on/off function. The flip-flop is thus driven with a pulse when the comparator output goes positive. Otherwise, the eight-to-ten-second sensor thermal recovery time could inhibit the S-R flip-flop and prevent the user from blowing the lamp out in a short time frame, immediately after they lit it with the match, if they chose to do that. Australia's electronics magazine Heat from the lamp When the lamp is running, it results in a temperature gradient along the brass tube, heating thermistor NTC2 more than NTC1. This reduces the offset voltage. To correct for this and make sure the sensor system does not become too sensitive, the lamp’s current flows through R26, an 11-turn coil of 32 AWG (0.2mm diameter) enamelled copper wire. This heats the NTC1 end of the brass tube to the tune of around 30mW, balancing out the thermal offset due to heat from the lamp. Blowing it out Blowing onto the sensor, the breath temperature is around 29°C, and it’s possible the ambient temperature is around that figure. Therefore, it’s unlikely we can detect blowing on the tube simply using a temperature change. On the other hand, the heat from a match or lighter is always significantly higher than ambient temperature, so it’s easy to detect. Therefore, the task of sensing when the lamp is ‘blown out’ was assigned to an electret microphone (MIC1). The output from the microphone is AC-coupled to an amplifier made from another op amp. A blow of air near the Magic Candle’s lamp/microphone port will reset the S-R flip-flop and switch off the lamp, even if the thermal sensor comparator output is still high. A blow of air from the mouth onto the area near the lamp from any direction is enough to switch it off. The microphone port does not have to be blown into directly; just blowing toward the lamp from any angle will extinguish it. The arrangement is resistant to background noise and, within limits, is quite stable. It’s a little easier to blow out than a real candle. The microphone arrangement is surprisingly resistant to moderate ambient noise. For example, holding the activated Magic Candle right at the output vent of a window air conditioner, running on full fan speed, won’t extinguish the lamp, nor will fairly loud voices or noises nearby, yet a blow on it from the mouth will easily do it. Standby mode & alternative switching methods When the Magic Candle has not been in use for a few minutes (the lamp is off), it goes into a super-lowpower shutdown mode with just 4nA siliconchip.com.au of current consumption. If the Magic Candle is inverted for a second or two and returned upright, gravity activates a mercury switch and the control circuitry returns to operating mode for three to four minutes. In this mode, it consumes around 20mA, waiting for the lamp to be lit by a match. If no match is available, inverting it again and holding it there for four seconds, then putting it back upright, provides an alternative method of lighting the lamp. The same technique can be used to switch it off if you don’t want to blow on it for some reason. More circuit details The circuit is more elaborate than I imagined it would be. For the lamp to receive power from the battery, PNP transistors Q1 & Q3 must be biased on. They are driven by N-channel Mosfets Q2 & Q4, respectively. The 470μF capacitor provides significant charge storage in the gate circuit of 2N7000 Mosfet Q2. When the Magic Candle is inverted, the mercury switch closes, and this capacitor is rapidly charged via diode D1 and the 120W current-limiting resistor to the battery voltage (less the forward drop of D1). This causes Q2 to conduct, bringing PNP transistor Q1 into saturation. At the same time, the S-R flip-flop is reset via diode D2, ensuring the lamp starts in the off state. The Magic Candle is now ‘armed’ and ready to be lit. If it is not lit after three to four minutes, the charge stored in the 470μF capacitor is depleted via the 750kW resistor and the lamp’s filament, and the circuit goes back into the low-­current standby mode. If the lamp is on, the current flow is reversed in the 750kW resistor, preventing the 470μF capacitor from discharging. So the lamp stays on unless the S-R flip-flop is toggled from the output of the microphone amplifier or the mercury switch/timer. One might wonder why the emitter of Q3 was not fed directly from the battery supply, which would gain an extra 60mV for the lamp. When the unit is in the process of powering down, after the lamp has not been on for some minutes, the OP495’s total power rail voltage falls below 2.6V. This can cause the S-R latch output, pin 7 of the OP495, to go positive and start recharging the 470μF timing capacitor. With the arrangement settled on, the current powering the lamp helps to pull down the op amp’s supply rail quickly, preventing the re-­activation of the lamp during switch-off. I used PNP transistors instead of Mosfets for Q1 & Q3 because they provide reverse battery protection since their base-emitter reverse breakdown voltage is higher than the battery supply of 4.5V. The intrinsic body diodes in Mosfets conduct with just a couple of volts in reverse across the channel. Regarding the lamp drive voltage, around 50mV is dropped by R26; the two saturation voltage drops of the ZTX951 transistors are only about 60-70mV each along with the internal resistance of the C cells, the result is an operating current of around 0.5-0.56A for the 6V 5W lamp. To allow the circuitry to operate down to low total battery voltages of around 2.2V, an LMC7660 (IC1) has been deployed to generate a negative voltage rail. This results in a near-­ doubled total voltage supply for the OP495 op amp. The LMC7660 operates down to 1.5V. A more modern version of this device, which is pin compatible, is the MAX1044. Of note, the original IC(L)7660 parts had a latch-up problem and required an external diode to prevent it. The LMC7660 and the Fig.4: the Magic Candle circuit is based around quad op amp IC2. Its V+ supply comes from the battery, while its Vsupply is a negative rail generated by IC1 from the battery supply. The roles of the four op amps within IC2 are shown by the dark blue text. PNP transistor Q1, driven by Mosfet Q2, is used to save power, while identical transistor Q3, driven by Mosfet Q4, switches the lamp. siliconchip.com.au Australia's electronics magazine December 2026  81 Fig.5: this simple circuit, with a variable power supply and voltmeter, lets you determine the threshold voltage of a 2N7000 Mosfet. Photo 4 (top): you insert the three C cells through this hole in the base. A metal plate attaches via the two exposed screw threads to hold them in and make electrical contact. Fig.6: assemble and wire up the PCB as shown here. Most axial components, like resistors and diodes, are mounted vertically on the PCB to save space. Watch the orientations of the diodes, shown by their cathode stripes here. Maxim part do not have the same concern, as far as I am aware. With the LMC7660, the minimum total voltage the op amp receives is in the order of 4V even with batteries discharged down to 2.2V (0.73V per cell). While there are very low voltage op amps available, I found it better to simply use a standard op amp with the boosted supply via the LMC7660, which has the additional benefit of creating a split supply. Component variances This design relies on properties of the 2N7000 Mosfets (Q2 & Q4) that are not guaranteed for every sample of the device. The data sheet for the 2N7000 suggested that the drain-source leakage current (with a zero gate-source voltage) could be as high as 1μA, but for the ones I tested, the leakage in this condition is around 4nA. Even if it were as high as 1μA, that would still take over 900 years to discharge the C cells! Ideally, the 2N7000 Mosfets should be selected for a low gate-source threshold voltage as this lowers the 82 Silicon Chip minimum operating voltage. If the 2N7000s are not selected parts, it will work, but it may stop working with the battery discharged to 2.5-3.0V rather than the 2.2V design target. I had seven 2N7000s in my junk box, and all but one had a gate threshold voltage close to 1.55V. The seventh was quite different, at 2.5V. The data sheet indicates it can range from 0.8V to 3V. A maximum of 1.6V is ideal for the project. Testing is simple, as shown in Fig.5. This uses a similar drain current to the operating circuit. As the power supply voltage in this setup is reduced, the drain voltage will fairly abruptly rise at some point. Above that gate-source (power supply) voltage, the drain voltage will stay low. I tested several 470μF 6.3V capacitors and their leakage resistance was typically at least 10MW. This does not present any difficulties here given the 750kW charge/discharge resistor. Construction Start by assembling the 25.5 × 68.5mm PCB, using the overlay Australia's electronics magazine Photo 5 (bottom): here’s the metal plate, held in place by two thumbscrews. diagram shown in Fig.6 as a guide. All the PCB pad holes are 0.7mm in diameter, except for the ones on the four corners and the two for the mercury switch strap. To keep it as compact as possible, many of the 1/8W resistors and diodes are mounted upright. 0.9mm PCB pins are used on the board corners. They provide plug-in connections for the two battery wires using their mating sockets. The pins near the lamp are soldered directly to the lamp socket tags. This attaches the PCB to the top disc. Overall assembly Fig.7 shows the basic dimensions. The size I made the base rings (Fig.8) was determined by the hole saws I had in my tool kit. They can be modified as desired. I used a white material called Bramite, but 8mm-thick white acrylic, HDPE or PEHD will also be suitable. I found that a 33mm hole cutter made a hole that was a little over 33mm and created an interference fit with the PVC tube, so no glue was required, but glue can be used. Photos 4 & 5 show the base assembly. siliconchip.com.au Fig.7: the overall configuration of the Magic Candle inside its PVC tube. Also shown on the left are the details of the metal strap that connects the battery positive terminal to the circuit board. Fig.8: this shows how I made the Candle base out of three rings with staggered sizes. You don’t have to make them exactly the same size as mine. December 2026  83 Thermal balance coil (R26): 11 turns of 32 AWG wire Fig.9: the details of the top cap and battery retaining plate. Fig.10: here is how to assemble the temperature-sensing brass tube with the two NTC thermistors inside it. Cable tie For the particular tube I used (purchased from Bunnings), making the diameter of the top disc around 29.4mm allowed it to be a tight press fit. Glue can be added if required. Making the outer diameter around 33.5mm closely matched the outer diameter of the pipe. A taper is a good idea on the top disc because then there is less shading of the light around the lamp’s base. The top disc (Fig.9) can be made of various white materials; FR4 fibreglass is fine, and it can be painted white. The light bulb socket has a flare on it where the lamp screws in, so the hole in the top disc needs to be made 10.5mm rather than 10mm. I wrapped some Scotch 27 tape around that to make sure the socket was a good central fit in the hole. There is a layer of clear heatshrink tubing on the wire side of the sensor tube. The enamelled 32 AWG wire is wound directly onto this. The top part of the sensor tube is painted with red VHT paint to make it obvious that the match should be held near it, and not near the microphone port. Making the sensor tube Photo 6: the PCB mounts vertically, with the thermal tube on one side and the microphone tube on the other. The construction of the sensor tube is shown in Fig.10. The two thermistors are at each end of a 34mm-long hollow 1/8in (3.175mm) diameter brass tube, spaced about 25mm apart. This tube is filled with non-conductive thermal paste. One end of the tube is a blind end (sealed with a small soldered brass disc). This part of the tube projects 11.5mm above the top surface of the Magic Candle. 2mm thick, 10mm OD O-ring Heatshrink sleeve Photo 7: a view of the control board from the opposite side compared to Photo 6, so you can see the microphone tube and insert. It’s a good idea to add an O-ring to acoustically isolate the microphone capsule from the Candle body. 84 Silicon Chip Australia's electronics magazine siliconchip.com.au A 14.5mm length of the tube projects inside the Candle body; 3mm of it there has an external metal sleeve. This helps it retain the heatshrink sleeve. The four wires from the two thermistors exit this end of the sensor tube. The wire end of the tube is sealed with two pieces of heatshrink sleeving, to retain the thermal paste. I found that the 1/8in brass tube was a good press fit into a 1/8in hole drilled in the top disc, because the particular tube measured 3.2mm even though 1/8in is officially 3.175mm. Model/hobby shops and eBay sellers stock this standard brass tube made by K&S Metals. All the 14-thou-thick (~0.3556mm) wall brass tubes they make are designed to slide inside each other. Sometimes they can be a firm fit and press together well. In the case that they are a little loose, they are easily soldered together, or glued if heat transfer is not required (such as with the microphone mount). Given that the internal diameter of the brass tube is 2.46mm, it could have been a little tight to pass the RS 151221 thermistor wires through the tube. However, the parts I received were a little smaller than their 2.4mm stated maximum diameter (just under 2mm) and were slightly ovoid. They come with bare wires. I used insulation taken from some thin insulated Kynar wire-wrap wire to insulate their bare wires. You can use any insulation tubing, but it must be very slim or you won’t get everything into the brass tube. The alternative RS thermistors specified are only 1.3mm in diameter, leaving more room for the lead wires. It would not be wise to increase the diameter of the brass tube for a larger thermistor, because that will increase the thermal inertia and delay the overall response to heating and cooling. When assembling the sensor tube, the thermal paste is introduced with a syringe and blunt needle. Insert the needle until it reaches the blind end and withdraw it as you slowly push the paste into the tube. Since each thermistor has the same length leads, it is easy to tell when they are ~25mm apart. The 11-turn coil that forms R26 can then be wound over that heatshrink sleeve (see Photo 6). Once the coil is wound, a small amount of epoxy resin can be used to keep the turns in place, or another piece of heatshrink sleeve could be placed over it. 1 double-sided PCB coded 05112251, 68.5 × 25.5mm 1 6V 5W MES base automotive lamp (LAMP1) 1 MES lampholder (LAMP1) [Jaycar SL2659] 1 mercury tilt switch (S1) 1 electret microphone insert with pins (MIC1) [Jaycar AM4011] 2 5kW NTC thermistors (NTC1, NTC2) [RS 151-221 or 484-0133] 1 200mm length of 32 AWG (0.2mm diameter) enamelled copper wire (R26) OR 1 300mm length of 30 AWG (0.25mm diameter) enamelled copper wire (17 turns) 4 0.9mm PCB pins 3 alkaline C cells Hardware & wire 1 241mm length of 33mm outer diameter, 27-30mm inner diameter (“25mm”) PVC pressure pipe [Holman PVP2512-1, Bunnings I/N 4770100] 1 25mm press-fit PVC pipe end cap 1 ~91mm diameter, 8mm-thick plastic disc (eg, white acrylic) 1 ~81mm diameter, 8mm-thick plastic disc (eg, white acrylic) 1 ~66mm diameter, 8mm-thick plastic disc (eg, white acrylic) 1 34mm length of 1/8in (3.2mm) diameter brass tube, 14 thou (0.35mm) wall thickness, 2.46mm inner diameter [K&S Metals #8127] 1 3mm length of 5/32in (4mm) diameter brass tube, 14 thou (0.35mm) wall thickness, ~3.2mm inner diameter [K&S Metals #8128] 1 18mm length of 7/32in (5.5mm) diameter brass tube, 14 thou (0.35mm) wall thickness [K&S Metals #8130] 1 4mm length of 1/4in (6.35mm) diameter brass tube, 14 thou (0.35mm) wall thickness [K&S Metals #8131] 1 4mm length of 9/32in (7.15mm) diameter brass tube, 14 thou (0.35mm) wall thickness [K&S Metals #8132] 1 4mm length of 5/16in (7.9mm) diameter brass tube, 14 thou (0.35mm) wall thickness [K&S Metals #8133] 1 brass end plug, 2.46mm diameter 1 50 × 50mm piece of 16 thou (0.4mm) thick brass sheet 1 225mm-long, 1/4in (6.35mm) wide, 25 thou (0.65mm) thick brass sheet 1 small tube of non-conductive thermal paste (eg, MX-4) 1 10mm outer diameter, 2mm-thick O-ring 1 small spring to retain C cells (eg, taken from a C cell holder) various lengths and colours of medium-duty hookup wire various fasteners (machine screws, nuts etc) and a small cable tie heatshrink tubing Semiconductors 1 LMC7660 or MAX1044 switched-capacitor voltage inverter, DIP-8 (IC1) 1 OP495 quad rail-to-rail op amp, DIP-14 (IC2) 2 ZTX951 60V 4A PNP transistors, TO-92 (Q1, Q3) 2 2N7000 N-channel Mosfets, TO-92 (Q2, Q4) 7 BAT46 small-signal schottky diodes, DO-35 (D1-D7) Capacitors 1 470μF 6.3V/10V electrolytic 3 47μF 16V tag tantalum 1 10μF 16V tag tantalum 1 1μF 63V/100V MKT 1 100nF 63V/100V MKT 1 100nF 63V/100V MLCC Resistors (all ⅛W ±5% axial unless noted) 1 10MW 1 10kW 1 4.7MW 1 8.2kW 1 1MW 1 4.7kW 1% 2 750kW 1 4.3kW 1% 6 100kW 2 270W 1 51kW 1 120W 2 47kW 1 0W 2 22kW siliconchip.com.au Australia's electronics magazine Parts List – Magic Candle December 2026  85 Photo 9: the completed top cap without the PCB attached. Photo 10: here you can see how the lamp base attaches to the top cap. Photo 11: the finished assembly, ready to insert into the Candle tube. Photo 12: I got the battery spring from a C cell holder. The thermal conductivity along the tube is dominated by the brass tube, not the paste within it. The paste helps with the thermal coupling of the thermistor bodies to the inner wall of the brass tube. An air gap here would not be helpful because air has only a fraction (0.3%) of the thermal conductivity of thermal paste. Microphone tube The microphone mounting tube (Fig.11) is inserted into a 5.5mm hole in the top disc until 2mm of it projects above the disc surface. It is a press fit because the outer diameter of the brass tube is 5.56mm (7/32in). Glue can be used if required. The three additional short sections of tubing can be glued to it or soldered if they are both brass. This creates a way to mount the microphone with a short section of heatshrink tubing. Since the diameter of heatshrink tubing doesn’t quite get small enough to get a good grip on the brass tubing, I added a cable tie. I also added a rubber O-ring (see Photo 7). This way, the microphone is not too sensitive to a knock on the candle’s housing. Photos 9 & 10 show the top plate with the lamp, thermal tube and microphone tube fitted to it. Photo 11 shows the same assembly with the PCB attached. Battery connections For the battery’s negative terminal, I made a ring of PVC taken from a tap fitting from Bunnings (Fig.12). However, there are other suitable materials. Photo 13: a view of the top battery contact from the Candle tube’s top. Fig.11: the microphone tube is somewhat simpler. The O-ring helps isolate it acoustically from the body of the Candle. 86 Australia's electronics magazine Silicon Chip I made it a firm press fit. When it was in position, I drilled a 0.9mm hole through the side wall of the tube and pressed in a 1 × 10mm-long pin to retain it. Since it was PVC, it could have been PVC-glued into position in the PVC pipe, but that would be permanent and could be messy. Still, the battery contact plate, spring and screws could be undone if any repairs were needed even with the PVC ring glued in position. Photo 12 shows the battery spring in place, taken from a C-cell holder. Photo 13 shows the negative battery terminal assembly fitted to the tube. The retaining pin can be seen projecting into the central hole a little, just below and to the right of the negative (black) wire as it passes up through the hole. The strap that connects the positive end of the battery to the PCB was shown earlier, in Fig.7. Once the Magic Candle is complete, remember to invert it briefly before trying to light it. Holding it inverted for a few seconds should cause it to SC switch on. Fig.12: how I made the battery negative terminal assembly. siliconchip.com.au Silicon Chip Binders REAL VALUE AT $21.50* PLUS P&P Are your copies of Silicon Chip getting damaged or dog-eared just lying around in a cupboard or on a shelf? Can you quickly find a particular issue that you need to refer to? Keep your copies safe, secure and always available with these handy binders These binders will protect your copies of S ilicon C hip . They feature heavy-board covers, hold 12 issues & will look great on your bookshelf. H 80mm internal width H Silicon Chip logo printed in goldcoloured lettering on spine & cover Silicon Chip Publications PO Box 194 Matraville NSW 2036 The Magic Candle shown just a little smaller than actual size. It provides a soft light suitable for setting the mood. siliconchip.com.au Australia's electronics magazine Order online from www. siliconchip.com.au/Shop/4 or call (02) 9939 3295 and quote your credit card number. *see website for delivery prices. December 2026  87