Silicon ChipInrush Current Limiter - December 2026 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: I seriously underestimated AI coding
  4. Feature: The History of AMD, Part 2 by Dr David Maddison, VK3DSM
  5. Project: Advanced Cable Analyser by Richard Palmer
  6. Project: Inrush Current Limiter by Phil Prosser
  7. Feature: Motor Control, Part 3 by Andrew Levido
  8. Project: NeoPixel RGB LED Analog Clock, Part 2 by Nicholas Vinen
  9. Feature: Working with AVR & PIC Fuses, Part 1 by Tim Blythman
  10. PartShop
  11. Project: The Magic Candle by Dr Hugo Holden
  12. Serviceman's Log: Working with switch-mode power supplies by Malcolm Batchelor et al
  13. Vintage Radio: STC Bantam model A141 by Ian Batty
  14. Subscriptions
  15. Market Centre
  16. Advertising Index
  17. Notes & Errata: PicoSDR, April 2026
  18. Outer Back Cover

This is only a preview of the December 2026 issue of Silicon Chip.

You can view 37 of the 104 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Articles in this series:
  • The History of AMD, Part 1 (November 2026)
  • The History of AMD, Part 2 (December 2026)
Items relevant to "Advanced Cable Analyser":
  • Advanced Cable Analyser main PCB [04101261] (AUD $5.00)
  • Advanced Cable Analyser lid PCB [04101262] (AUD $10.00)
  • Advanced Cable Analyser software and documentation (Free)
  • Advanced Cable Analyser PCB patterns (PDF download) [04101261-2] (Free)
  • Cutting/drilling diagrams for the Advanced Cable Analyser (Panel Artwork, Free)
Items relevant to "Inrush Current Limiter":
  • Inrush Current Limiter PCB [10110261] (AUD $7.50)
  • Inrush Current Limiter PCB pattern (PDF download) [10110261] (Free)
Articles in this series:
  • Motor Control, Part 1 (October 2026)
  • Motor Control, Part 2 (November 2026)
  • Motor Control, Part 3 (December 2026)
Items relevant to "NeoPixel RGB LED Analog Clock, Part 2":
  • BZ-121 miniature GNSS receiver (Component, AUD $30.00)
  • Neo-7M GPS module with onboard SMA connector & 5-pin header (Component, AUD $20.00)
  • VK2828U7G5LF TTL GPS/GLONASS/GALILEO module with antenna and cable (Component, AUD $25.00)
  • New RGB LED 'Analog' Clock kit (Component, AUD $85.00)
  • New RGB LED 'Analog' Clock firmware (Software, Free)
Articles in this series:
  • NeoPixel RGB LED Analog Clock, Part 1 (November 2026)
  • NeoPixel RGB LED Analog Clock, Part 2 (December 2026)
Items relevant to "The Magic Candle":
  • Magic Candle PCB [05112251] (AUD $2.50)
  • Magic Candle PCB pattern (PDF download) [05112251] (Free)
  • Magic Candle assembly diagrams (Panel Artwork, Free)

Purchase a printed copy of this issue for $15.00.

▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ ▶ siliconchip.com.au ▶ ▶ I decided to power the circuit from a Current Limiter ▶ ▶ Design decisions Inrush ▶ T his Inrush Current Limiter is designed to ‘soft start’ large power amplifiers and power supplies, although it would likely have application in other places, such as starting modestly sized motors. The principle is very simple: insert a fixed resistance in series with the mains input to the transformer for the first second (or so) of operation, then short it out with a power relay. This allows the inrush current to be reduced before the relay removes the resistance from the circuit and allows the full current required for operation. We also provide an open-collector output to act as a disable input for an amplifier during power-on, minimising the current draw from the amplifier while the capacitor bank charges. For switch-mode power supplies, it is common to use a negative temperature coefficient (NTC) thermistor as an inrush current limiter. These have a resistance of a few tens of ohms initially, but as current flows through them and they heat up, the resistance drops to a fraction of the initial value, to around 1W. The advantage of these is simplicity – all you need to do is insert the device in series. However, for a serious power amplifier, we would need several of these in parallel. Even so, we would need to accept a voltage drop across them, and at high currents, these devices run hot – between 150°C and 200°C. Furthermore, if you interrupt power for a short time, they won’t have time to cool down, and they don’t help with that inrush current on the second and subsequent switch-on events. One way of avoiding the voltage losses and dissipation of NTC thermistors used for inrush current limiting is to put a relay across them and switch it on after a delay, shorting the thermistor(s) out. That also has the benefit of letting them cool down sooner. However, once you’re doing that, you have the option to use wire-wound power resistors instead, bringing the further advantage that their effectiveness no longer depends on temperature. So if you switch the unit off and on rapidly, they will be just as effective each time, although they will get hotter than they would from a single switch-on event. So they need to have a high power rating. By Phil Prosser While testing a power supply with a 600VA toroidal transformer and a substantial capacitor bank, I frequently tripped the circuit breaker on my switchboard. This simple circuit limits the inrush current for this type of power supply, saving the hassle and making power-up much less eventful! ▶ Limits mains current draw to about 7A when an appliance is switched on ▶ Rapid detection of mains interruption, ensuring reliable soft starting ▶ The control circuitry is isolated from the mains ▶ Programmable 1-10s delay with a resistor (default is 1s) ▶ Open-collector output for disabling speakers or other loads while starting up ▶ Not affected by rapid on/off cycling ▶ Maximum load current: 8A Australia's electronics magazine December 2026  45 standalone transformer on the board. It may seem extravagant to add an extra transformer when we are likely limiting the inrush of a large transformer, but we do not want to be subject to the regulation of the large transformer. If there is a heavy load on that transformer, there is the potential for its output to droop, and we don’t want that affecting the operation of the Inrush Current Limiter. Furthermore, our onboard power supply has been sized so that if the mains input drops significantly below 220V AC, it will continue to operate under both start up and mains fault conditions; including brownouts. Given that the source impedance of a mains socket is not zero, the appliance will have a cord (possibly a long one), and may even be plugged in via an extension cord, when drawing tens of hundreds of amps, it is not unlikely for the voltage seen at the socket to be substantially lower than nominal. If the mains input is interrupted briefly, an NTC inrush limiter will not work. Our circuit detects a brief loss of mains, switches the limiter in and drives the open collector disable active. This adds a couple of parts to the circuit but it is an important feature. This circuit has parts connected directly to the Active mains conductor. To ensure maximum safety, the transformer isolates all but the relay and 10W resistors from the mains. Because it’s floating, we can safely connect the ground of the Inrush Current Limiter to an external circuit, allowing Why large amplifiers draw so much current at switch-on There are a couple of reasons why large linear power supplies, like those used in high-power Class-A or Class-AB amplifiers, draw such a high current initially. 1. Charging the capacitor bank. When the reservoir capacitors are fully discharged, they initially present a very low impedance to the rectifier. The charging current is limited mainly by the transformer winding resistance and leakage inductance, rectifier and wiring resistance and the ESR of the capacitors. In a large amplifier, the initial current can easily reach tens of amps. 2. Transformer magnetising inrush. Toroidal transformers, which are commonly used in high-power amplifiers, can draw an exceptionally large magnetising current when first energised. Transformer core flux depends on the integral of the applied voltage, so switching on near a mains-voltage zero crossing can produce a flux excursion much greater than occurs during normal operation. Any remanent magnetisation left in the core can make this worse, potentially driving the core into saturation. The resulting current can briefly reach hundreds of amps in a large transformer. Switch-mode power supplies can also have high inrush currents. Small EMI suppression capacitors connected across the mains can produce a very brief current spike as they charge, although this is generally not the main source of inrush. More importantly, most mains-powered switch-mode supplies rectify the mains to produce high-voltage DC, with a substantial electrolytic capacitor connected to the DC bus. When the supply is first switched on, this capacitor is discharged and can draw many tens of amps through the bridge rectifier unless some form of inrush-current limiting or controlled pre-charge is provided. the open-collector limit active output to be used. The delay required to reduce inrush current is quite short. Usually, a handful of cycles is all that is required, so a few hundred milliseconds. The recommended configuration implements a one-second delay. The delay is controlled by a single resistor value, which is 10kW for the default delay of one second. Changing this to 2.2kW will make it more like 200ms, while increasing it will make the delay much longer, up to 10 seconds with 100kW. However, if increasing the delay, you need to consider the thermal limitations of the current-­ limiting resistors, discussed later. The open-collector output uses a BC548 NPN transistor and can sink up to 20mA reliably. The maximum load current is defined by the PCB; the PCB traces are 7mm wide, so they can safely handle 8A continuously. The relay itself is rated at 16A; you have to derate that for inductive loads like transformers, but since it’s switching when the voltage across the 10W power resistors is already quite low, it isn’t being worked hard. Circuit description Scope 1: the yellow trace is the unregulated DC supply voltage across the 470μF capacitor, while the cyan trace is the negative end of the relay coil. The relay is energised close to one second after power is applied. 46 Silicon Chip Australia's electronics magazine The circuit of the Inrush Current Limiter is shown in Fig.1. At power on, RLY1 is off, so mains current and voltages comes in via the ACTIVE IN terminal of CON2, through the three 100W resistors in parallel, then to the ACTIVE OUT terminal to power the main toroidal transformer and whatever else runs from mains in the amplifier. Only the Active current flows through this board; Neutral and Earth will be wired to the power socket externally. The Neutral connection on CON2 siliconchip.com.au Fig.1: most of the circuit is involved in controlling RLY1 so that it switches on one second after power is applied, shorting out the resistors that the Active current otherwise has to flow through, between pins 1 & 2 of CON2. It’s also designed to switch RLY1 off quickly after mains power is lost. is to power this board, and there is no Earth terminal, as the circuitry is floating. The Inrush Current Limiter circuit is powered from the mains input via a 3VA transformer, bridge rectifier and 470μF filter capacitor, producing a roughly 17V unregulated DC supply. That is dropped to a regulated 12V DC by REG1, which powers the rest of the circuit. The rest of the circuit is essentially a time delay so that NPN transistor Q5 switches on roughly one second after mains power is applied, energising RLY1 and shorting out the 100W resistors. When that happens, mains current to the appliance flows in via ACTIVE IN, through the relay contact(s) and out through ACTIVE OUT, bypassing the 100W resistors. When mains power is switched off, the circuit is designed to switch RLY1 off immediately so that the 100W resistors are back in-circuit in case power is switched on immediately again. Timer Initially at power-on, the 100μF capacitor will be discharged and thus diode D7 will be reverse-biased. Q3’s base is pulled up to +12V by the 100kW resistor, so Q3 is off and so are Q5 and Q6. The relay is not energised. The 100μF capacitor starts charging via siliconchip.com.au its series 10kW resistor (or whatever value you’ve chosen). The 100μF capacitor has to charge to about 8.2V before anything happens. At that point, there’s enough voltage to forward-bias diode D7 and transistor Q3’s base-emitter junction. This happens at 8.2V due to the voltage across 6.8V zener diode ZD1 plus D7’s forward voltage (~0.7V) and Q3’s base-emitter junction forward bias voltage (~0.7V). At that stage, Q3, Q5 and Q6 switch on, the relay is energised and the inrush current limiting resistors are shorted out by the relay – see Scope 1. Note that during this process, transistor Q1 is switched off and so it has no effect on the charging of the 100μF capacitor. We can verify this by looking at the rest of the circuit. When there is an AC output voltage from transformer T1, periodically NPN transistor Q4 will switch on. When it’s on, it discharges the 100nF capacitor at its collector, so that capacitor can never charge sufficiently to switch off PNP transistor Q2 due to the time constant with the 100kW resistor (100kW × 100nF = 10ms, but it needs several time constants to charge sufficiently). Thus, Q2 is switched on the whole time that mains is applied to the circuit, and it pulls up the base of PNP Australia's electronics magazine transistor Q1, preventing it from switching on. About 75ms after mains power is removed, with Q4 off, the 100nF capacitor at the base of Q2 charges to about 11.5V, switching Q2 off and Q3 on and rapidly discharging the 100μF capacitor. Q3, Q5 & Q6 then all immediately switch off and the relay is de-energised, with D5 clamping its back-EMF voltage spike. Timing The time constant for the 100μF capacitor charging and thus the relay switching is one second for R = 10kW and C = 100μF. Since this is linearly proportional to R, all you really need to know is that doubling the value of R doubles the time delay, and halving it will halve the time delay. Suitable values range from about 2.2kW (<250ms) to 100kW (5-10s). Transformer options For transformer T1, we’ve chosen a small PCB-mounting 3VA transformer from Altronics. Using this results in minimal mains wiring, so the result is neat and tidy. We’ve slotted the secondary holes so a standard 25mm-pitch PCB-mounting transformer can be used instead, such as Myrra’s 44199, available from element14. December 2026  47 Parts List – Inrush Current Limiter 1 double-sided 110.5 × 88.5mm PCB coded 10110261 1 2-way polarised header, 2.54mm pitch (CON1; optional) 1 3-way 5/5.08mm mains-rated terminal block (CON2) [Altronics P2039] 1 PCB-mounting safety fuse holder (F1) [Altronics S5987, Mouser 693-0031.3553] 1 200mA fast-blow M205 fuse (F1) 1 255VAC 16A SPST PCB-mount relay, 12V DC coil (RLY1) [Altronics SA4198 or Hongfa HF14FW/012-HST(136)] 1 3VA 6+6V output mains transformer (T1) [Altronics M7012A, Myrra 44199] 1 micro-U TO-220 heatsink and mounting hardware (optional; see text) [Altronics H0630] 1 100mm length of 1.6mm diameter heatshrink tubing 1 21 × 25mm piece of insulating material (eg, acrylic or Presspahn) 2 12mm nylon tapped spacers 4 M3 × 6mm plastic/nylon machine screws M3 mounting hardware to suit application Semiconductors 1 7812 12V 1A linear regulator, TO-220 (REG1) 3 BC558 30V 100mA PNP transistors, TO-92 (Q1-Q3) 3 BC548 30V 100mA NPN transistors, TO-92 (Q4-Q6) 1 6.8V 400mW/500mW axial zener diode, DO-35/DO-41 (ZD1) 4 1N4004 400V 1A power diodes, DO-41 (D1-D4) 5 1N4148 75V 150mA signal diodes, DO-35 (D5, D7-D10) Capacitors 1 470μF 25V/35V electrolytic capacitor 1 100μF 25V electrolytic capacitor 3 100nF 50V/63V/100V ceramic or MKT capacitors Resistors (all ¼W ±1% axial unless noted) 2 100kW 8 10kW (7 if using a timing resistor value other than 10kW) 3 100W 10W ±5% wirewound [Altronics R0435] Fig.2: assembly is straightforward and all parts are through-hole types. Start with the lower-profile components and work your way up to the taller ones, watching the orientations of the diodes and transistors. Change the resistor labelled in red for a different timeout (higher value = longer, lower = shorter). 48 Silicon Chip Australia's electronics magazine If you need to use a transformer with flying leads, such as Altronics’ M2851A, we have included holes in the PCB that allow you to use cable ties to secure the wires to the PCB. We are also using a PCB-mounting safety fuse holder, with a 200mA fuse for the 3VA transformer. There is room for a small flag heatsink on the regulator, but this would only be required if your transformer outputs more than 12V AC. Construction The Inrush Current Limiter is built on a 110.5 × 88.5mm PCB that’s coded 10110261. Use the overlay diagram, Fig.2, as a guide during construction. Start by fitting all the small resistors. We are recommending a 10kW timing resistor (value shown in red). This gives a one-second soft start, which worked well for our large test amplifier. If you are not using the open-­collector output to disable your speakers or load, a delay of 200ms (use 2.2kW) would be worth considering. Follow by fitting the diodes. Do not mix up the sole zener diode, the small 1N4148 signal diodes and larger 1N4004 parts. Make sure the cathode stripes all face as shown in Fig.2. The three-way terminal block needs to be mains-rated; Altronics Cat P2039 is suitably rated for this application. Mount it now, plus CON1 if you will be using it. Now install all the transistors. There are three each of the NPN (BC548) and PNP (BC558) devices, so don’t mix them up. Other transistors from this series, like the BC547/BC557 and BC549/BC559, could also be used. Make sure the flat faces are orientated as shown. Follow these with the voltage regulator, capacitors and fuse holder. The heatsink for REG1 isn’t required if you’re using the recommended transformer, but it wouldn’t hurt if you fit it. Finally, load the relay, the 10W resistors and the transformer. Add short lengths of heatshrink tubing to these resistor leads before you solder them so that once the board is running, there is no possibility of you touching these legs. Testing Connect a DC power supply set to 15V DC or more, with its negative output connected to the GND test point siliconchip.com.au Figs.3 & 4: a suggestion for how to wire the unit up. It’s pretty simple. We haven’t shown anything connected to CON1 here; many applications won’t require it. Cut the shield shown here from a small piece of insulating material like acrylic or Presspahn and attach it with plastic tapped spacers and plastic machine screws so you can’t accidentally come in contact with the live screws on the top of terminal block CON2. in the lower left of the board and the positive to the “+UNREG” test point, which is next to the 470μF capacitor. Apply power and check the voltage on the 12V test point in the top-right corner of the board. This should be 12V ±0.5V. The relay will not click in as there is no AC present. If it doesn’t work: • Is the 12V rail OK? If not, is the DC input OK? • If the output is low, is the regulator hot? If so, something is likely shorted to ground. • Is the 470μF capacitor the right way around? • Are the transistors and diodes in the right way around? Tack a piece of hookup wire to TP1, which is just near the top left of the transformer. With the DC power supply on, touch this to the +UNREG test point. This should enable the AC presence detection system and the relay should click in after about a second. If this works, everything is good. Once the board operates from the DC supply as above, you are ready to install it. Insert a 200mA M205 fuse into the fuse holder. Wire the Inrush Limiter into your circuit as shown in Fig.3, ensuring that all the mains wiring is secured using cable ties. Cut the shield shown in Fig.4 from a sheet of Presspahn, acrylic or similar insulating material, drill two 3mm siliconchip.com.au holes as shown and mount it on nylon tapped spacers using plastic/nylon screws via the two holes in the PCB. This covers the terminal block so you can’t come into accidental contact with the live screws on the top. Apply power and check that the relay clicks in after about a second. If it does not, power it down, wait for all capacitors to discharge and investigate. Usage quickly as we could, and repeating. These twelve cycles took about 90 seconds. At the end, after discharging and unplugging everything, the resistors were at about 50°C. This is an unrealistic test, as if your speakers are disabled at power off, the main rails will not collapse in the few seconds we took to discharge them with a 4W resistor. So this suggests the resistors will not live a stressful life with normal usage. SC We tested this with a 600VA transformer loaded with 35,000μF capacitors on both rails. Without the Inrush Limiter, the power board’s 20A circuit breaker would kick out with alarming regularity. With the Inrush Limiter in circuit, the start-up was much more sedate; no thumps from the transformer and everything was controlled. One concern is how much dissipation occurs in the 10W resistors. We ran twelve cycles of turning the circuit on, then off, discharging the main capacitors as The assembled board. The heatsink is optional. Australia's electronics magazine December 2026  49