Silicon ChipThe Philco 4-Valve Mantel Set - December 2010 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: Desalination plants make heavy reliance on technology
  4. Feature: Soldering SMDs: It’s Becoming Unavoidable by Nicholas Vinen
  5. Feature: Recycle Your Cordless Drill – Make It Corded by Leo Simpson
  6. Project: A Hot-Wire Cutter With Inbuilt Heat Controller by John Clarke
  7. Project: Digital/Analog USB Data Logger by Mauro Grassi
  8. Project: Digital Lighting Controller For Christmas Light Shows, Pt.3 by Nicholas Vinen
  9. Project: A High-Quality DAB+/FM Tuner, Pt.3 by Mauro Grassi
  10. Project: Build A Hearing Loop Level Meter, Pt.2 by John Clarke
  11. Vintage Radio: The Philco 4-Valve Mantel Set by Rodney Champness
  12. Book Store
  13. Advertising Index
  14. Outer Back Cover

This is only a preview of the December 2010 issue of Silicon Chip.

You can view 17 of the 104 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Items relevant to "A Hot-Wire Cutter With Inbuilt Heat Controller":
  • Hot Wire Cutter Controller PCB [18112101] (AUD $5.00)
  • Hot Wire Cutter PCB pattern (PDF download) [18112101] (Free)
  • Hot Wire Cutter front panel design (PDF download) (Panel Artwork, Free)
Items relevant to "Digital/Analog USB Data Logger":
  • PIC18F27J53-I/SP programmed for the Universal USB Data Logger [0411210A.HEX] (Programmed Microcontroller, AUD $20.00)
  • Universal USB Data Logger Software [0411210A.HEX] (Free)
  • Universal USB Data Logger User Manual (PDF download) (Software, Free)
  • USB Data Logger panel artwork (PDF download) (Free)
Articles in this series:
  • Digital/Analog USB Data Logger (December 2010)
  • Digital/Analog USB Data Logger (December 2010)
  • Digital/Analog USB Data Logger, Pt.2 (January 2011)
  • Digital/Analog USB Data Logger, Pt.2 (January 2011)
  • Digital/Analog USB Data Logger, Pt.3 (February 2011)
  • Digital/Analog USB Data Logger, Pt.3 (February 2011)
Items relevant to "Digital Lighting Controller For Christmas Light Shows, Pt.3":
  • Digital Lighting Controller LED Slave PCB [16110111] (AUD $20.00)
  • Digital Lighting Controller Slave Unit PCB [16110102] (AUD $25.00)
  • dsPIC33FJ64GP802-I/SP programmed for the Digital Lighting Sequencer/Controller [1611010A.HEX] (Programmed Microcontroller, AUD $25.00)
  • Firmware and PC software for the Digital Lighting Controller [1611010A.HEX] (Free)
  • Digital Lighting Controller LED Slave PCB pattern (PDF download) [16110111] (Free)
  • Digital Lighting Controller Master PCB pattern (PDF download) [16110101] (Free)
  • Digital Lighting Controller Slave PCB pattern (PDF download) [16110102] (Free)
  • Digital Lighting Controller master unit front panel design (PDF download) (Panel Artwork, Free)
  • Digital Lighting Controller mains slave unit front panel design (PDF download) (Panel Artwork, Free)
Articles in this series:
  • Digital Controller For Christmas Light Shows (October 2010)
  • Digital Controller For Christmas Light Shows (October 2010)
  • Digital Lighting Controller For Christmas Light Shows, Pt.2 (November 2010)
  • Digital Lighting Controller For Christmas Light Shows, Pt.2 (November 2010)
  • Digital Lighting Controller For Christmas Light Shows, Pt.3 (December 2010)
  • Digital Lighting Controller For Christmas Light Shows, Pt.3 (December 2010)
Items relevant to "A High-Quality DAB+/FM Tuner, Pt.3":
  • Software for the DAB+ Tuner (Free)
Articles in this series:
  • A High-Quality DAB+/FM Tuner, Pt.1 (October 2010)
  • A High-Quality DAB+/FM Tuner, Pt.1 (October 2010)
  • A High-Quality DAB+/FM Tuner, Pt.2 (November 2010)
  • A High-Quality DAB+/FM Tuner, Pt.2 (November 2010)
  • A High-Quality DAB+/FM Tuner, Pt.3 (December 2010)
  • A High-Quality DAB+/FM Tuner, Pt.3 (December 2010)
Items relevant to "Build A Hearing Loop Level Meter, Pt.2":
  • Hearing Loop Level Meter PCB pattern (PDF download) [01111101] (Free)
  • Hearing Loop Level Meter panel artwork (PDF download) (Free)
Articles in this series:
  • Build A Hearing Loop Level Meter (November 2010)
  • Build A Hearing Loop Level Meter (November 2010)
  • Build A Hearing Loop Level Meter, Pt.2 (December 2010)
  • Build A Hearing Loop Level Meter, Pt.2 (December 2010)

Purchase a printed copy of this issue for $10.00.

Vintage Radio By RODNEY CHAMPNESS, VK3UG The Philco 40-40 4-Valve Mantel Set Designed as a “wartime special”, the Philco 40-40 is simple 4-valve receiver that was manufactured in Sydney in 1940/41. It’s a compact reflexed design with some interesting features. R ADIO RECEIVER design has gone through many phases, both in regard to circuit design and cabinet styling. The very first designs were basically crystal sets but there were also sets that used other forms of solidstate detectors. Valves were only just being developed at that time and in any case, the early types were much too expensive for experimenters to buy. The next phase saw the development of coffin-style radios based on one or more valves. These were often built by experimenters, with the parts laid out on a breadboard. This was 92  Silicon Chip then housed in a coffin-style cabinet to protect the wiring. Coffin-style receivers were superseded in the late 1920s by commercial receivers built on metal chassis. The period leading up to WWII was a time of rapid development in both component and circuit design and many excellent receivers were produced. The Great Depression hit hard during the early 1930s and manufacturers responded by producing simple receivers at low prices. As the depression receded, more elaborate designs were again produced towards the end of the 1930s. Then along came WWII and the emphasis changed again. Because of military demands, component supplies were restricted during the war years and manufacturers had to use whatever they could obtain. As in the Great Depression, the emphasis was on austerity. However, radio design had progressed considerably over this decade and the WWII austerity models are considerably better than those of the depression years. One local manufacturer from that era was Philco Radio and Television Corporation (Aust.) Pty Ltd. Based in Auburn, NSW, they produced radio receivers from the 1930s through to at least the mid-1950s. These covered the complete range, from simple receivers up to complex multiband sets. The Philco set described here is an austerity WWII model, circa 1940-41. It was designated the “40-40” and is a 4-valve set with a reflexed IF/audio amplifier stage. General details The Philco 40-40 is basically a compact mantel receiver. It’s housed in a Bakelite cabinet but despite its compact size, it still weighs in at 4.5kg. This particular set has a cream cabinet although it’s fairly certain that brown cabinets would also have been available and there may have been other colours as well. As shown in the photos, the dial scale on the Philco 40-40 is squareshaped. The pointer, however, is attached to the tuning gang shaft and sweeps through a 180° arc to cover a nominal frequency range of 5501600kHz. A simple dial-cord drive couples the tuning control to the dial drive drum and the dial cord will be easy to replace when the time comes. A 5-inch (125mm) electrodynamic speaker is mounted on the lefthand front of the chassis and the unit fitted to this particular set was still in surprisingly good condition. There are siliconchip.com.au Fig.1: the Philco 40-40 employs a 4-valve reflexed circuit, with the 6B7 doing double-duty as both an IF amplifier and a first audio stage. In addition, the 6B7 functions as the detector. just two controls, located beneath the dial scale: the volume control at left and the tuning control at right. There is no on/off switch – after all, this was a WWII austerity model. Crowded house From the rear of the receiver, it can be seen that things are quite crowded above the chassis. In fact, there is only about 5mm between the tops of some valves and the inside top of the cabinet. The same applies to one of the IF transformers. This chassis was really shoe-horned into the cabinet! Despite this, the chassis is easy to remove from the cabinet. It’s just a matter of removing the two knobs at the front and the three screws that go through the bottom of the cabinet into the chassis. The assembly then slides out. I initially didn’t notice that the cabinet had been repaired during a restoration several years ago. The repair job was expertly done and only close inspection reveals the colourmatched fibreglass matting covering some extensive cracks. Circuit details Now let’s take a look at the circuit – see Fig.1. This is a 4-valve reflexed siliconchip.com.au receiver and for those unfamiliar with the concept, take a look at Vintage radio for July 2010. Unfortunately, the way that the circuit has been drafted leaves quite a lot to be desired. As an example, resistor 38 and potentiometer 45 on the cathode of the 6A8G could easily have been positioned to the left of the valve and arranged vertically. That way, their function would have been much more obvious at first glance. The antenna coil is a flat basketweave type of the style commonly fitted to portable receivers. It’s located at the righthand end of the chassis and has two tappings so that the most appropriate one can be selected to suit the antenna being used. As shown on Fig.1, the output of the tuned circuit is fed to the signal grid of the 6A8G which functions as a converter. In this particular set, a 6J8G has been fitted although a 6A6G is the correct type to use. The oscillator section uses a single coil winding (2), with the “earthy” end going to the relevant valve grid to give the necessary feedback to induce oscillation. This receiver does not have AGC so the cathode circuit is connected to earth via a 300Ω resistor (38) and a series 7.5kΩ potentiometer (45). The setting on the pot determines the bias on the signal grid of the 6A8G and hence its gain. This in turn controls the volume of the receiver. IF stage The intermediate frequency (IF) signal appears at the plate of the 6A8G and is fed through two tuned circuits in the first IF transformer to the grid of a 6B7. This functions as the IF and first audio valve. Here, the signal is amplified and then fed via a single-tuned IF transformer to one of the detector diodes in the 6B7. Note that the circuit indicates that this second IF transformer is double tuned, as both windings appear to have tuning slugs. However, the secondary has no fixed capacitor across it, so it is not tuned and there is no adjustment for that winding (AWA also often used this same style of IF transformer to feed the diode detector). Once again, the draughtsman has been careless in drawing the circuit. The detected audio is fed to the grid of the 6B7 via resistor 37, capacitor 20 and the secondary winding of the first IF transformer. The resulting amplified audio signal appears across a 100kΩ resistor (41) and is applied via capacitor 37 (10nF) to the grid of a 6V6 December 2010  93 This front view shows the compact nature of the chassis. Despite this, it still manages to include a 5-inch (125mm) electrodynamic loudspeaker. lines in order to be sure that the correct terminals have been used. My tests revealed that the transformer has three primary winding taps to suit voltages centred on 200V, 240V and 260V AC. I also discovered that the person who originally restored this set had wired the mains Neutral to a tap and the Active to the common transformer terminal. That’s certainly not the recommended way to do it. On the circuit diagram, it states that a 6F7 was originally used in the IF/ audio preamplifier stage but this was changed to a 6B7 after run 1250. All the valves in this set are octal except this one valve but they may have had lots of 6B7s in stock and wanted to use them (the 6G8G is the octal equivalent). It’s also possible that some valves types were unavailable during the war years and they had to make do with what was available. Chassis layout The chassis is a tight fit, with barely 5mm between the tops of the valves and the inside top of the cabinet. All the alignment adjustments are accessible via holes at the back of the chassis. audio output valve. This then drives the electrodynamic loudspeaker via a speaker transformer. Note that the cathode of the 6V6G is earthed and its bias is supplied via a back bias network from the power supply. Power supply The power supply is a little unusual in that the field coil/filter choke (6) is wired into the negative lead to earth. The more conventional method is to connect it in series with the positive HT lead from the rectifier filament. The back bias for the 6V6G audio 94  Silicon Chip output valve is developed across the field coil. This bias is applied to the 6V6 via a resistive divider consisting of a 250kΩ resistor (43) and a 100kΩ resistor (42). This divider reduces the back bias voltage to around -12V, which is optimum for a 6V6G. A 100nF capacitor (30) filters any hum on the back bias line. Note that the earth at the junction of (42) and (30) is poorly shown in the circuit diagram (it really is a confused circuit schematic). The labelling of the various power transformer input taps is missing too. This makes it necessary to measure the voltages on the filament The components used in this compact mantel set are all full-sized. As a result, the designers had quite a job on their hands when it came to shoehorning everything into the available space. As mentioned earlier, the space between the valves and the inside top of the cabinet is just 5mm. Both the front-end parts and the power supply components are adjacent to the power transformer which is mounted under the chassis, directly below the tuning gang. The oscillator coil is right alongside the power transformer, while the converter valve is at the front of the chassis, near the loudspeaker and the tuning gang. The 5Y3G rectifier is located at the back of the chassis next to the tuning gang, while the 6B7 is at the lefthand end of the chassis (viewed from the front) alongside the speaker transformer. The (shiny) second IF transformer is underneath the chassis, while the 6V6G sits on top of the chassis in the back lefthand corner. Because of its layout, this isn’t an easy set to work on and it can be difficult to identify particular leads, especially when they disappear under other parts. The wiring colours have also faded and this adds to the difficulty of tracing individual leads. One quite interesting aspect of the layout is that all the antenna, oscillator and IF adjustments are accessible from the back of the set, without removing the chassis from the cabinet. In parsiliconchip.com.au ticular, the trimmers for the antenna and oscillator circuits are accessed via three holes along the bottom edge of the back skirt of the chassis. The designers must be applauded for this unique idea, which makes alignment much easier than otherwise. Restoration This receiver had been restored several years ago, prior to my friend buying it. This meant that it required only minor work to get it back to peak performance. As can be seen in the photos, the chassis has surface rust but the set itself is quite clean. Unfortunately, stripping it down to remove the rust would be a huge amount of work. As a result, it was decided to leave it as it was and simply restore the circuit to proper working order. The mains cord Earth lead had originally been soldered to the chassis, which was considered satisfactory in years gone by. This had subsequently been changed by terminating the Earth lead with a crimp connector and fastening this to one of the transformer mounting bolts (see photo). I wasn’t happy with this and bolted the earth lead crimp connector to the chassis instead. A separate earth lead was then run from one of the transformer mounting bolts to a second chassis earth point. In addition, the Active and Neutral leads were transposed on the power transformer by resoldering them to the correct terminals. The method used by a previous restorer to secure the mains cord was quite primitive and is completely unsatisfactory. It should be properly secured using an approved chassis clamp and the owner will attend to this when he takes the set home. The paper capacitors had all previously been replaced, as had the electrolytic capacitors. I wonder how the old ones fitted in, as they would have taken up quite a lot of the space under the chassis and space really is at a premium. Unfortunately, some of the replacement parts have been fitted with their values obscured. Wherever possible, I always fit resistors and capacitors so that their values can be easily read. This makes it much easier to service a set should it later require attention. For some reason, the previous restorer had installed a 700pF mica siliconchip.com.au The parts are tightly packed together on both the top and bottom of the chassis, although access is still reasonable. Note the primitive method used by a previous repairer to secure the mains lead. It should be secured using an approved chassis clamp, while the Earth lead should be bolted directly to the chassis, rather than secured to a transformer mounting screw. capacitor in the padder circuit of the oscillator instead of a 475pF capacitor as specified. This error was discovered when I later switched the receiver on (see below). receiver with a loudspeaker field-coil filter. It then settled down to about 250V as the valves began drawing current. Initial tests The next step was to attach an antenna to one of the antenna coil taps. When I did this, the set immediately began working. What’s more, it seemed quite sensitive, with lots of stations coming in. Because the Philco 40-40 has no AGC (automatic gain control), I had to constantly adjust the volume control as I tuned across the broadcast band. AGC certainly has its advantages and continued on page 103 It was now time to test the receiver. I began by checking the leakage between the windings of the power transformer using my high-voltage tester and this showed that it was in good order. In addition, there were no shorts or near shorts on the HT (high tension) line. Having completed these checks, I connected a meter to the HT line and applied power. The HT shot up to over 400V initially, which is normal in a Alignment December 2010  95 34 Chan 500mHZ LOGIC ANALYSER Vintage Radio – INTRONIX * RS232, I2C, SPI, CAN Interpreters * USB powered * Data compression T +GS * +/- 6 Volt threshold * Advanced multi level triggering * Ideal for microprocessor debugging 440 $ SuperPro Device Programmers Fastest low cost programmers! Standalone & USB. Socket adapters. 02 4567 8999 www.digitalgraphics.com.au Issues Getting Dog-Eared? Keep your copies safe with these handy binders REAL VALUE AT $14.95 PLUS P & P Price: $A14.95 plus $10.00 p&p per order (includes GST). Just fill in and mail the handy order form in this issue; or fax (02) 9939 2648; or phone (02) 9939 3295 and quote your credit card number. Available in Australia only. continued from page 95 in this set, could easily have been applied to the converter stage. One thing I noticed was that the stations weren’t quite where they should be on the dial. As a result, I decided to start the alignment procedure with the local oscillator. Testing revealed that the receiver was tuning even lower in frequency than the IF (460kHz), which was decidedly odd. It was then that I found the 700pF fixed padder capacitor that had been fitted by the previous restorer, instead of the 475pF capacitor specified. I replaced the padder with the specified value and was then able to correctly align the oscillator stage. Once that had been done, the stations came in at their correct locations on the dial. Finally, the loop antenna was adjusted for optimum performance at around 1500kHz by peaking the associated trimmer capacitor (9). This was done with a long-wire antenna connected first to one antenna tap and then the other. The old Philco receiver was now really hitting its straps and it really does perform well for a 4-valve austerity model set. In fact, on the strongest local stations, the volume could only be reduced down to a comfortable listening level, although it could be adjusted for zero output on weaker stations. There’s a good reason to prefer sets with good AGC systems and audio stage volume controls. Summary This is an interesting little receiv- Looking for real performance? • • • • The antenna coil is a flat basket-weave type similar to that commonly fitted to portable receivers. er that’s well worthwhile having in a collection. Despite being a “wartime special”, it’s quite a good performer although it would have benefited by having AGC. As mentioned above, all the alignment adjustments are accessible without removing the chassis from the cabinet. This feature is unique to this set as far as I know and it’s certainly very convenient. Finally, because the parts are so tightly packed into the chassis, this would not have been easy to service when using full-sized components. The designers certainly did a good job getting so much into such a small SC cabinet. 160 PAGES 23 CHAPTE Learn how engine management systems work RS Build projects to control nitrous, fuel injection and turbo boost systems Switch devices on and off on the basis of signal frequency, temperature and voltage Build test instruments to check fuel injector duty cycle, fuel mixtures and brake & temperature Price: Aust. $A19.80 plus $A10 P&P ($A12 P&P NZ; $A18 P&P elsewhere) – see the order form in this issue. Order by phoning (02) 9939 3295 & quoting your credit card number; or fax the details to (02) 9939 2648; or mail your order with cheque or credit card details to Silicon Chip Publications, PO Box 139, Collaroy, NSW 2097. siliconchip.com.au From the publi shers of Intelligent turbo timer I SBN 095852 294 9 78095 8 -4 TURBO BO OST & nitrous fuel con 5229 trollers 46 $19.80 (inc GST) NZ $22.00 (inc GST) How engin e management works December 2010  103