Silicon ChipThe Admiral 5BW mantel receiver - September 2006 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: Australia's energy policies should rely heavily on natural gas
  4. Project: Turn an Old Xbox Into A $200 Multimedia Player by Julian Edgar
  5. Feature: Thomas Alva Edison – Genius; Pt.1 by Kevin Poulter
  6. Feature: Transferring Your LPs to CDs & MP3s by John Clarke
  7. Project: PICAXE Net Server, Pt.1 by Clive Seager
  8. Review: “Wachit” – It Turns A VCR Into A Security Recorder by Murray Downes
  9. Project: The Galactic Voice by John Clarke
  10. Project: Aquarium Temperature Alarm by Peter Smith
  11. Project: S-Video To Composite Video Converter by Jim Rowe
  12. Salvage It: The good bits in old receivers by Julian Edgar
  13. Vintage Radio: The Admiral 5BW mantel receiver by Rodney Champness
  14. Book Store
  15. Advertising Index
  16. Outer Back Cover

This is only a preview of the September 2006 issue of Silicon Chip.

You can view 36 of the 112 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Articles in this series:
  • Thomas Alva Edison – Genius; Pt.1 (September 2006)
  • Thomas Alva Edison – Genius; Pt.1 (September 2006)
  • Thomas Alva Edison – Genius, Pt.2 (October 2006)
  • Thomas Alva Edison – Genius, Pt.2 (October 2006)
Articles in this series:
  • PICAXE Net Server, Pt.1 (September 2006)
  • PICAXE Net Server, Pt.1 (September 2006)
  • PICAXE Net Server, Pt.2 (October 2006)
  • PICAXE Net Server, Pt.2 (October 2006)
  • PICAXE Net Server, Pt.3 (November 2006)
  • PICAXE Net Server, Pt.3 (November 2006)
  • PICAXE Net Server, Pt.4 (December 2006)
  • PICAXE Net Server, Pt.4 (December 2006)
Items relevant to "The Galactic Voice":
  • PCB patterns for the Galactic Voice (PDF download) [08109061/2] (Free)
  • Galactic Voice control panel artwork (PDF download) (Free)
Items relevant to "Aquarium Temperature Alarm":
  • PICAXE-08M software for the Aquarium Temperature Alarm (Free)
  • PCB pattern for the Aquarium Temperature Alarm (PDF download) [03109061] (Free)
  • Aquarium Temperature Alarm front panel artwork (PDF download) (Free)
Items relevant to "S-Video To Composite Video Converter":
  • PCB pattern for the S-Video to Composite Video Converter (PDF download) [02109061] (Free)
  • S-Video to Composite Video Converter front panel artwork (PDF download) (Free)

Purchase a printed copy of this issue for $10.00.

Vintage Radio By RODNEY CHAMPNESS, VK3UG The Admiral 5BW mantel receiver Domestic valve radios with PC boards were relatively uncommon, with most manufacturers sticking to point-to-point wiring until the end of the valve era. One exception to this rule was the Admiral 5BW mantel receiver. I NSTEAD OF using PC boards, domestic transistor radios were initially built the same way as valve receivers were – ie, with point-to-point wiring. The transistors were also sometimes mounted in sockets, just like valves. Of course, today we look on such techniques as archaic and totally unsuited to modern technology. Everything is now on PC boards and point-to-point wiring is minimised if not eliminated altogether. Valve radio receivers were traditionally built using a metal chassis to which all the major components (eg, transformers, valve sockets, tuning gang, etc) were attached. The wiring was all point-to-point which made the assembly slow and expensive. However, some manufacturers did start using PC boards in valve radios in the late 1950s. We looked at one of these, the Healing 412E, back in February 2001. Admiral, an American firm, also built valve radios with PC boards in Australia but their technique was somewhat different to Healing’s. Admiral 5BW mantel receiver Admiral Australia Pty Ltd was locat­ed in Gow St, Bankstown, NSW and began manufacturing domestic radios and TV receivers in the mid 1950s. However, they apparently only remained in this field for a few years. The Admiral 5BW receiver looks much like any other “plastic” mantel receiver of the era. Internally, however, it was different from other receivers in that it used a PC board to mount most of the parts. The only items not mounted on the 100 x 100mm PC board were the ferrite-rod antenna, the combined volume/on-off/tone control, This is the fully-restored Admiral 5BW in its case. Also shown is the barrel nut that secures the dual volume/tone control assembly. 98  Silicon Chip siliconchip.com.au Fig.1: the Admiral 5BW receiver is a fairly conventional superhet receiver with five valves and a loopstick antenna. the loudspeaker and its transformer, the tuning gang and the power transformer. As shown in the photos, the chassis is very sparsely populated except on the PC board. Certainly, if the manufacturer had wanted to, the set could have been made much smaller. Circuit details Although the circuit is conventional, it has a few features that were not commonly used in Australian-designed receivers. For example, the input tuned circuit consists of a 200mm-long x 9mm-dia­ meter ferrite rod with a coupling coil and lead so that an external antenna can be connected to the set. There is no earth lead as such – instead, the set relies on the capacitance between the primary winding of the power transformer and the other windings and the chassis to provide a defacto earth via the mains. Unfortunately, this isn’t the best way to achieve optimum reception, as the mains has electrical noise on it. This noise is coupled into the antenna circuit, giving less than perfect reception in many cases. Additionally, a purpose-made earth ensures that a stronger signal is achieved at the input siliconchip.com.au This view shows the chassis with the 6VA6 removed so that the M2 “couplate” can be seen (arrowed). This contains numerous components assembled into a 7-pin module for PC board mounting. circuit, as the mains “earth” is not all that efficient. The converter stage uses a 6BE6 and is quite conventional, although it has little standing bias and relies on the fact that the high tension (HT) voltage is relatively low. In addition, the set will normally be tuned to a station and hence AGC voltage will be applied. The tuning range of the receiver is 535-1670kHz which means that it requires some tweaking to reach the lowest frequency on the broadcast band (531kHz). By contrast, at the high-frequency end, it can tune to a number of the special broadcasting services in the 1600-1700kHz subband. The output of the converter is at 455kHz and this is fed to the IF (intermediate frequency) stages. The 455kHz IF is amplified by a neutralised 6BA6 amplifier and this has cathode bias applied to it in addition to AGC voltage. The neutralising September 2006  99 This view shows the front of the chassis after removal from the case. Note the dual volume/tone control assembly at bottom left. capacitor is C9 (4.7pF ceramic) which is in a bridge circuit. Another arm of the neutralising circuit is C8 which is the AGC bypass capacitor. With this neutralising scheme, neither of these components should be altered to the nearest available value if replacement is required, otherwise the stage could oscillate at 455kHz. The next valve in the line-up is a 6AV6 which serves a multiple role as the diode detector, AGC amplifier and first audio amplifier. The grid has contact potential bias applied to it and the coupling between the plate of the 6AV6 and the following 6AQ5 output valve is conventional. However, although the 6AV6 circuit is conventional, the way in which it is made is not. Instead of point-to-point wiring, all the parts (including three resistors and five capacitors) are assembled into a 7-pin module that’s suitable for PC-board mounting. The downside to this is that some faults require that the entire module 100  Silicon Chip be removed for repairs. This isn’t easy because of the limited room adjacent to it on the chassis. This is highlighted by the arrow pointing to the M2 “Couplate” in one of the photographs. On the other hand, the “Couplates” are fairly reliable. Quite a few of the capacitors in the set are ceramic (which are more reliable than paper capacitors) and the “Couplate” also uses ceramic capacitors. The audio output stage uses a 6AQ5 with cathode bias. The speaker transformer is mounted on the loudspeaker frame, which in turn is mounted on the front of the cabinet. This assembly is connected via a flying lead and a 4-pin plug into a socket on the chassis. Note that although the circuit shows only two leads from the transformer, there are in fact four wires in total because of negative feedback from the voice coil. As shown in Fig.1, the cathode of the 6AQ5 is connected via the voice coil to earth and the valve is supplied with back bias. In fact, the circuit diagram and the actual circuit are different in several areas. However, these differences are minor and should not present a problem to restorers. The tone control circuit in the plate circuit of the 6AQ5 is poorly thought out in my opinion. The potentiometer is “live” at 200V DC (not the 170V shown on the circuit diagram) which places some strain on its insulation and is also a trap for unwary fingers. If the position of the capacitor and the potentiometer had been transposed in the circuit, there would be no DC voltage on the potentiometer and the whole set-up would have been safer. Cleaning the cabinet The instructions in the service manual for dismantling the set are quite clear although they don’t completely cover the set I have. However, the chassis isn’t hard to remove. First, the centre piece of the “handspan” dial was unscrewed. The dial then siliconchip.com.au Want cheap, really bright LEDs? We have the best value, brightest LEDs available in Australia! Check these out: Luxeon 1, 3 and 5 watt All colours available, with or without attached optics, as low as $10 each Low-cost 1 watt Like the Luxeons, but much lower cost. •Red, amber, green, blue and white: Just $6 each! Lumileds Superflux These are 7.6mm square and can be driven at up to 50mA continuously. •Red and amber: $2 each •Blue, green and cyan: $3 each Asian Superflux Same as above, but much lower cost. •Red and amber: Just 50 cents each! •Blue, green, aqua and white: $1 each. Go to www.ata.org.au or call us on (03)9419 2440. WHERE can you buy SILICON CHIP This page from the service manual shows the specifications of Admiral’s 5BW. Also shown is some basic servicing information, including the PC board layout. came away easily as did the concentric volume and tone control knobs. That done, the four screws used to secure the back of the cabinet were removed. There were no other screws holding the set in the cabinet but it was still fastened by the volume and tone controls. Closer inspection revealed that these controls are attached to the front panel by a barrel nut over the control shafts. Removing this then allowed the chassis to slide out of the cabinet as far as the speaker leads would allow. siliconchip.com.au Why do manufacturers leave leads just too short for effective access or maintenance to be carried out? In this case, I wanted to be able to check the set with the chassis out of the cabinet, so I extended the speaker leads. I had worked on this receiver several years ago, so the cabinet was in reasonable condition and only required a small amount of effort to get rid of any minor blemishes. However, inside the cabinet there are a number of burn marks which are too deep to remove. Just how these burn marks occurred is You can get your copy of SILICON CHIP every month from your newsagent: in most it’s on sale on the last Wednesday of the month prior to cover date. You can ask your newsagent to reserve your copy for you. If they do not have SILICON CHIP or it has run out, ask them to contact Network Distribution Company in your state. SILICON CHIP is also on sale in all stores . . . again, you can ask the store manager to reserve a copy for you. Or, to be sure that you never miss an issue and save money into the bargain, why not take out a subscription? The annual cost is just $83 within Australia or $89 (by airmail) to New Zealand. Subscribers also get further discounts on books, and other products we sell. September 2006  101 Most of the parts are on the PC board, so there’s not a lot to see under the chassis. As a result, the chassis depth is quite shallow. something of a mystery, as there are no hot components in their vicinity. Fixing the faults As normal, I began by checking the insulation between the chassis and the mains wiring using my 1000V insulation tester. This measured OK, however I also used an earth leakage circuit breaker on the mains as an extra precaution, as this set only had a 2-core power lead fitted during these initial tests. It was later fitted with a 3-core lead, so that the chassis could be earthed (which is much safer). As stated previously, this set used quite a few ceramic capacitors, particularly in locations were leakage could pose problems. However, I wasn’t happy with the leakage of the only paper capacitor on the PC board – a 100nF unit across the 100V line. This was replaced with a polyester type and the set then switched on. As it came on, I made sure that the HT rose to the correct level and that the rectifier wasn’t showing any red plates, which would indicate a short or near short on the HT line. During my previous work on this set, I had cleaned away the muck that had accumulated on the horizontallymounted PC board. This had been quite difficult to remove due to the crowded nature of the circuit board. It had even effected the components so that they all now looked much the same colour and making it difficult to decipher resistor and capacitor values. As a result, the new resistors I fitted really do stand out from the dull-looking original components. Of course, the board would not have required anywhere near as much cleaning if it had been mounted vertically. Anyway, the set had worked quite well when checked over several years ago but its performance had now deteriorated quite markedly. So what had gone wrong with the set? The IF amplifier was now quite regenerative and this had sharpened up the response such that the audio output was quite “bassy”. I began by checking the metal shields fitted to the 6BE6 and the 6BA6 valves as these now appeared quite rusty. As a result, I cleaned the insides of the shields with sandpaper and bent the earthing fingers to ensure a positive connection to each shield. This made little difference, so I then tried another 6BA6 with the result that there was now no output from the set. The reason wasn’t hard to find – its heater wasn’t alight. Initially, I thought it must be a dud valve so I substituted another one but the same thing happened. I then refitted the original valve and its and the heater lit up! So what was going on? The filaments of the two new valves I have substituted were quite OK so I tried closing up the valve socket pins using a small pointed scriber. That fixed the heater problem and the set was also now quite stable when using one of the replacement valves. Evidently, there is a problem with the original valve that causes the instability but I’m not throwing it out, as it may be quite OK in a different circuit. However, I have marked it as suspect so that I don’t get caught out further down the track. Although the set was now stable, the sensitivity was down and the IF was off tune, with its centre frequency down around 430kHz. As a result, I Issues Getting Dog-Eared? Keep your copies safe with these handy binders. REAL VALUE AT $12.95 PLUS P & P Available Aust. only. Price: $A12.95 plus $7 p&p per order (includes GST). Just fill in and mail the handy order form in this issue; or fax (02) 9939 2648; or ring (02) 9939 3295 and quote your credit card number. 102  Silicon Chip siliconchip.com.au Photo Gallery: Peter Pan BKM 4-Valve Radio MANUFACTURED IN 1948 by Eclipse Radio, South Melbourne, the Peter Pan BKM was a 4-valve reflex superheterodyne housed in a rounded bakelite cabinet that was very modern for the era. This example is housed in the less common green cabinet. The valve line-up was as follows: 6A8-G frequency changer; 6B8-G reflexed IF amplifier/1st audio amplifier/detector/AVC rectifier; 6V6-GT audio output; and 5Y3-GT rectifier. Photo: Historical Radio Society of Australia, Inc. tried adjusting the cores to bring it up to 455kHz, which is the correct frequency, and found that I could adjust all but one core which was stuck. I then tried running some machine oil down the stuck core, after which I was able to adjust it. However, I was still unable to get this core to adjust the tuned circuit to 455kHz and I was beginning to suspect the mica capacitor inside this unit. Unfortunately, this particular IF transformer is a sealed unit, so I was unable to dismantle it to fix the problem. In the end, I simply replaced it with an IF transformer salvaged from another Admiral chassis. This replacement IF transformer was then adjusted to 455kHz but although the performance was better, it was still not up to scratch. A quick check of all the RF valves did not reveal any problems, so I decided to take a closer look at the antenna circuit. In particular, I noticed that the antenna coupling coil on the loopstick was quite some distance from the earthy end of the tuned winding. siliconchip.com.au So did it have enough coupling? To find out, I wound about half a dozen turns of insulated enamelled wire onto the earthy end of the tuned winding and found that this noticeably improved the performance. I am now satisfied that I’ve got as good a performance from this set as I can reasonably expect. Summary Admiral was one of the first manufacturers to use PC boards and they nearly got everything right with this set. However, with the benefit of hindsight, the PC board could have been mounted vertically and all the fixed capacitors other than electrolytics should have been ceramic types for greater reliability (polyester capacitors weren’t readily available at that time). The set itself is neat and functional and makes a good kitchen mantel receiver. Finally, although my set is cream in colour, it was also available in red, turquoise and green. It is a set worth having in any collection. SC September 2006  103