Silicon ChipA battery eliminator & a simple servicing aid - October 2000 SILICON CHIP
  1. Outer Front Cover
  2. Contents
  3. Publisher's Letter: The health record card - what a smart idea
  4. Feature: DrDAQ: It Turns Your PC Into A Science Lab by Peter Smith
  5. Feature: Structured Data Cabling For The Home by Ross Tester
  6. Project: Guitar Jammer For Practice & Jam Sessions by Peter Smith & Leo Simpson
  7. Project: Booze Buster Breath Tester by Ross Tester
  8. Project: I Spy With My Little Eye Cavity Camera by Ross Tester
  9. Project: Installing A Free-Air Subwoofer In Your Car by Julian Edgar
  10. Project: Protoboards: The Easy Way Into Electronics, Pt.2 by Leo Simpson
  11. Project: Fuel Mixture Display For Cars, Pt.2 by John Clarke
  12. Feature: Drive By Wire: Electronic Throttle Control; Pt.2 by Julian Edgar
  13. Product Showcase
  14. Review: Altronics' Aussie-Made PA Amplifiers by Ross Tester
  15. Order Form
  16. Vintage Radio: A battery eliminator & a simple servicing aid by Rodney Champness
  17. Book Store
  18. Notes & Errata
  19. Back Issues
  20. Market Centre
  21. Advertising Index
  22. Outer Back Cover

This is only a preview of the October 2000 issue of Silicon Chip.

You can view 42 of the 96 pages in the full issue, including the advertisments.

For full access, purchase the issue for $10.00 or subscribe for access to the latest issues.

Items relevant to "Guitar Jammer For Practice & Jam Sessions":
  • Guitar Jammer PCB pattern (PDF download) [01110001] (Free)
  • Guitar Jammer panel artwork (PDF download) (Free)
Articles in this series:
  • Protoboards: The Easy Way Into Electronics, Pt.1 (September 2000)
  • Protoboards: The Easy Way Into Electronics, Pt.1 (September 2000)
  • Protoboards: The Easy Way Into Electronics, Pt.2 (October 2000)
  • Protoboards: The Easy Way Into Electronics, Pt.2 (October 2000)
  • Protoboards: The Easy Way Into Electronics, Pt.3 (November 2000)
  • Protoboards: The Easy Way Into Electronics, Pt.3 (November 2000)
  • Protoboards: The Easy Way Into Electronics, Pt.4 (December 2000)
  • Protoboards: The Easy Way Into Electronics, Pt.4 (December 2000)
Items relevant to "Fuel Mixture Display For Cars, Pt.2":
  • PIC16F84(A)-04/P programmed for the Fuel Mixture Display [AIRFUEL.HEX] (Programmed Microcontroller, AUD $10.00)
  • PIC16F84 firmware and source code for the Fuel Mixture Display [AIRFUEL.HEX] (Software, Free)
  • Fuel Mixture Display PCB patterns (PDF download) [05109001/2] (Free)
  • Fuel Mixture Display panel artwork (PDF download) (Free)
Articles in this series:
  • Fuel Mixture Display For Cars, Pt.1 (September 2000)
  • Fuel Mixture Display For Cars, Pt.1 (September 2000)
  • Fuel Mixture Display For Cars, Pt.2 (October 2000)
  • Fuel Mixture Display For Cars, Pt.2 (October 2000)
Articles in this series:
  • Drive By Wire: Electronic Throttle Control; Pt.1 (August 2000)
  • Drive By Wire: Electronic Throttle Control; Pt.1 (August 2000)
  • Drive By Wire: Electronic Throttle Control; Pt.2 (October 2000)
  • Drive By Wire: Electronic Throttle Control; Pt.2 (October 2000)

Purchase a printed copy of this issue for $10.00.

VINTAGE RADIO By RODNEY CHAMPNESS, VK3UG A battery eliminator, a servicing aid & getting the good oil A battery eliminator is virtually a must if you want to run battery-powered vintage receivers. This month, we take a look at the Monarch battery eliminator, describe a simple servicing stand for record turntables and tell you where to look for information on vintage radio. Almost from day one, battery eliminators were used to reduce the cost of running battery-powered radios. That’s because portable radios were so convenient that they were often used in the home as well as outdoors, but the cost of running a set on batteries alone was prohibitive. To overcome this problem, the radio manufacturers developed mains-powered battery “eliminators”. The Monarch BLK battery eliminator of 1947 is one such device and was a big improvement on the designs used in the 1920s. Monarch equipment was made by Eclipse Radio and family resemblances to Peter Pan and Astor can be seen. The Monarch’s nominal output voltages suits sets using 1.4V valves with 90V high tension (HT). Physically, it is about twice the size of two 45V batteries and it has just one control – an on-off switch. The unit, in its original form, had a 4-core lead and an octal plug on the end of the lead so that it could plug into the sets that it was designed to power. I decided that The Monarch BLK battery eliminator front panel is shown at left, while above shows the unit removed from the case. The D-size cell can be seen at top right and this functioned as a filter/regulator for the 1.4V rail. 82  Silicon Chip ELECTRONIC VALVE & TUBE COMPANY The Electronic Valve & Tube Company (EVATCO) stocks a large range of valves for vintage radio, amateur radio, industrial and small transmitting use. Major current brands such as SOV-TEK and SVETLANA are always stocked and we can supply some rare NOS (New - Old stock) brands such as Mullard, Telefunken, RCA and Philips. Hard to get high-voltage electrolytic capacitors and valve sockets are also available together with a wide range of books covering valve specifications, design and/or modification of valve audio amplifiers. Fig.1: circuit diagram of Monarch BLK Battery Eliminator. It used a power transformer with two secondary windings, one for the 90V HT rail and the other for the 1.4V rail (to supply the valve filaments). Note the lack of a mains earth, even though the device was built into a metal case (see text). I would use it as a general-purpose eliminator instead of one designed specifically for particular sets hence the unterminated wiring on the unit shown in the photos. To dismantle it, the control knob is first removed and the front panel sprung to remove it. After that, it’s simply a matter of undoing three screws so that the works can be removed from the case. As can be seen from the circuit diagram (Fig.1), the unit is quite simple and so the restoration is also simple. There are two secondary windings on the transformer – a high-voltage wind­ing to supply nominally 90V for the HT supply and a centre-tapped 6V (3V + 3V) winding to power the filaments and indicator lamp. The high-voltage winding employs a half-wave dry metal “Westalite” rectifier. The HT is filtered in the normal way using two electrolytic capacitors and a 1kΩ resistor and this is quite effective. The actual HT voltage developed depends on the current drain. With no load, it is around 115V. The designed maximum current drain is 20mA. It is much harder to filter and maintain a low tension rail of 1.4V, compared to a 90V rail. In this case, the CT trans­ former secondary winding drives a full-wave “Westalite” rectifier and this gives a no-load voltage of 4.1V which, if connected directly to the valve filaments, would blow them instantly. So how did the manufacturers get the voltage down to 1.4V? Well, they did it in a couple of ways which, by today’s stan­ dards, were rather crude. First, the voltage drop across the filter chokes at currents of 250400mA reduced the output voltage to somewhere near 1.4V. However, with such a wide current varia­tion available from the supply, the output voltage could still be much too high for the valve filaments and would burn them out. This meant that the output voltage had to be regulated in some way and this was done by switching a 1.5V “D” cell across the output when the unit was turned on. As a result, the filament voltage is held within tolerance. The cell also has another function – it acts as a large filter element so PO Box 487 Drysdale, Victoria 3222. Tel: (03) 5257 2297; Fax: (03) 5257 1773 Mob: 0417 143 167; email: evatco<at>mira.net New premises at: 76 Bluff Road, St Leonards, Vic 3223 Silicon Chip Binders REAL VALUE AT $12.95 PLUS P&P  Heavy board covers with 2-tone green vinyl covering  Each binder holds up to 14 issues  SILICON CHIP logo printed on spine & cover Price: $A12.95 plus $A5 p&p each (Australia only) Just fill in & mail the handy order form in this issue; or fax (02) 9979 6503; or ring (02) 9979 5644 & quote your credit card number. October 2000  83 through the cord-entry grommet – a common technique in those days. If you decide to restore this type of equipment, the mains cord should be replaced with a 3-wire type so that the metal case can be correctly earthed. In addition, the cord should be proper­ly secured using an approved clamp or cordgrip grommet. If you have any doubts about what you are doing, seek advice from someone who’s qualified. In summary, this little unit is a simple but effective battery eliminator from the early post WWII era. These days, of course, much more effective and versatile battery eliminators can be built, which have precise regulation at several nominated output voltages. What’s more, they will accurately maintain these output voltages over wide variations in the amount of current drawn. Servicing stand This is the underside view of the battery eliminator chassis. Note the knot in the mains cord to anchor it and the lack of earthing for the metal case (only a 2-wire mains cord was used) – two things that wouldn’t pass muster nowadays. A correctly anchored 3-wire mains cord with the earth lead connected to chassis is the next step in the restoration process and will greatly improve safety. that the filament supply is very close to pure DC. Monarch recommended that this “D” cell be replaced every 12 months. If the unit hasn’t been abused, all that will be necessary to do is check for hum on both the HT and LT supply lines. If a set connected to the supply hums, try replacing all the electro­ lytic capacitors with equivalent value units. In this unit, there are only four of them, so this is hardly an arduous exercise. If you have a digital voltmeter, switch it to an AC range and, with a capacitor of around 0.47µF in series with one of its leads, connect it across each of the DC supply rails in turn. In each case, there should be no readings on the meter after the 0.47µF series 84  Silicon Chip capacitor has been charged. On the 1.4V line, even the 10V AC range of a conventional moving coil meter is unlikely to register any hum voltage unless the filtering is completely ineffective. A digital meter has more chance of indicating if any hum is present. Electrical safety And here a note about electrical safety. By today’s stan­ d ards, this device certainly wouldn’t meet the safety requirements of electrical authorities. For starters, it was only fitted with a twin-core power cord which meant that the metal case wasn’t earthed. Second, the power cord was “anchored” by tying a knot in it inside the case, so that is couldn’t be pulled Last month, I described the restoration of an HMV Nipper­gram. In that column, I briefly mentioned that the changer mechanism was tested by mounting it on a “servicing board” (or stand) so let’s now take a closer look at this simple yet invalu­ able servicing aid. In order to check the operation of a record changer, it must be mounted horizontally and you must be able to view the mechanism underneath the frame while it is operating. This is not always easy to do and many’s the time I’ve laid on the floor with a torch shining on the works in an attempt to see how it all worked. This simple aid makes the job much easier. It consists of nothing more than several lengths of 9.5mm dowel and a 300 x 450mm piece of particle board (about 19mm thick) which is drilled to a grid pattern. The dowel pieces are “plugged” into appro­priate locations on the board and used to support the turntable at several points as shown in one of the photos. This makes it easy to inspect the mechanism as the turntable operates. If you want to make your own, drill the holes using a drill press (if possible) so that all they are perpendicular to the board. The holes are approximately 25 mm apart but don’t be too pedantic about that, as variable spacing will help fit the dowel ends between components on the changer or an upturned receiver chassis. Generally, four dowels will be enough to support any chassis or changer. I have four 300mm dowels for observing what’s going on with record changers and four 175mm dowels for mounting up­turned receiver chassis. In fact, a variety of dowel lengths can be cut to suit whatever you are servicing/restoring. The 9.5mm dowels are quite rigid and I don’t recommend using anything thinner as they can break too easily and your changer or receiver chassis could end up on the floor. To stop the mounted unit from moving around, I fitted a 6mm rubber chair tip to one end of each dowel. This involved machining (or filing and sanding) one end of each dowel piece to 6mm but the result is worth it. So there you have it – a simple lowcost device that will make servicing and restoring record changers just that bit easi­er. Getting the good oil How do vintage radio buffs get into this rewarding pastime of restoring radio and television equipment and collect­ i ng the paraphernalia that goes with it, such as books, posters, magazines and the like? My collecting started around 30 years ago. An advertise­ment appeared stating that a chap wanted to sell a military radio transceiver to someone who would restore it, before our radio history disappeared. That caught my attention, so I started collecting portable army transceivers from WWII. That’s how my collecting days started but how did yours? Perhaps this article is your first exposure to this interesting hobby. If you want to find out more, other magazines, both past and present, can be valuable sources of information. New magazines With the first burst of enthusiasm, it is likely that a new vintage radio enthusiast will grab just about anything on the subject and treat all that is said as gospel. Regrettably, some books and magazines are not really good sources of information and it is only when you become knowledgeable that you can sort the wheat from the chaff. It’s a bit of a catch 22 situation, really. Generally, American electronics/ radio magazines don’t offer a great deal for vintage radio enthusiasts in Australia and New Zealand. The main reason for this is that the American This simple servicing stand is invaluable when it comes to checking record changers but is also useful when servicing radio receivers. It allows you to inspect the mechanism of a record changer while it is operating. magazines cover 110V equipment and describe bits and pieces that are sometimes hard to obtain here. However, the various vintage radio groups in America do have their own publications and some of these are quite good. Sometimes, these are available through the Historical Radio Society of Australia (HRSA) or the New Zealand Vintage Radio Society (NZVRS). In addition, the HRSA and the NZVRS have their own respective in-house magazines – “Radio Waves” and the “NZVRS Bulletin”. These both concentrate heavily on vintage radio and are excellent for enthusiasts but you do have to be a member to obtain copies. On a similar theme, some of the vintage radio clubs in Australia (and probably in New Zealand too) have in-house news­letters. Old magazines Old radio/wireless magazines make very interesting reading and will give you an excellent feel for vintage radio. If you can get them, copies of “Wireless Weekly”, “Radio & Hobbies” and “Radio, Television & Hobbies” up to about 1965 are well worth collecting and reading. Of these, “Radio & Hobbies” probably provides the most relevant information for vintage radio enthusiasts. It also featured “The Serviceman Who Tells” column, which discussed the faults found in radios (and later, TV sets) in the period from 1939. These columns make good reading and now provide practical restoration tips. There were also many constructional articles, such as the “Little General” 4-valve radios, which I and many others found useful over the years. Finally, old magazines are particularly interesting because they trace the evolution of radio month by month. A lot of good stuff can be gleaned from SC their pages. October 2000  85